Version:  2.6.34 2.6.35 2.6.36 2.6.37 2.6.38 2.6.39 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14

Linux/drivers/video/Kconfig

  1 #
  2 # Video configuration
  3 #
  4 
  5 menu "Graphics support"
  6         depends on HAS_IOMEM
  7 
  8 config HAVE_FB_ATMEL
  9         bool
 10 
 11 config SH_MIPI_DSI
 12         tristate
 13         depends on (SUPERH || ARCH_SHMOBILE) && HAVE_CLK
 14 
 15 config SH_LCD_MIPI_DSI
 16         bool
 17 
 18 source "drivers/char/agp/Kconfig"
 19 
 20 source "drivers/gpu/vga/Kconfig"
 21 
 22 source "drivers/gpu/host1x/Kconfig"
 23 
 24 source "drivers/gpu/drm/Kconfig"
 25 
 26 config VGASTATE
 27        tristate
 28        default n
 29 
 30 config VIDEO_OUTPUT_CONTROL
 31         tristate "Lowlevel video output switch controls"
 32         help
 33           This framework adds support for low-level control of the video 
 34           output switch.
 35 
 36 config VIDEOMODE_HELPERS
 37         bool
 38 
 39 config HDMI
 40         bool
 41 
 42 menuconfig FB
 43         tristate "Support for frame buffer devices"
 44         ---help---
 45           The frame buffer device provides an abstraction for the graphics
 46           hardware. It represents the frame buffer of some video hardware and
 47           allows application software to access the graphics hardware through
 48           a well-defined interface, so the software doesn't need to know
 49           anything about the low-level (hardware register) stuff.
 50 
 51           Frame buffer devices work identically across the different
 52           architectures supported by Linux and make the implementation of
 53           application programs easier and more portable; at this point, an X
 54           server exists which uses the frame buffer device exclusively.
 55           On several non-X86 architectures, the frame buffer device is the
 56           only way to use the graphics hardware.
 57 
 58           The device is accessed through special device nodes, usually located
 59           in the /dev directory, i.e. /dev/fb*.
 60 
 61           You need an utility program called fbset to make full use of frame
 62           buffer devices. Please read <file:Documentation/fb/framebuffer.txt>
 63           and the Framebuffer-HOWTO at
 64           <http://www.munted.org.uk/programming/Framebuffer-HOWTO-1.3.html> for more
 65           information.
 66 
 67           Say Y here and to the driver for your graphics board below if you
 68           are compiling a kernel for a non-x86 architecture.
 69 
 70           If you are compiling for the x86 architecture, you can say Y if you
 71           want to play with it, but it is not essential. Please note that
 72           running graphical applications that directly touch the hardware
 73           (e.g. an accelerated X server) and that are not frame buffer
 74           device-aware may cause unexpected results. If unsure, say N.
 75 
 76 config FIRMWARE_EDID
 77        bool "Enable firmware EDID"
 78        depends on FB
 79        default n
 80        ---help---
 81          This enables access to the EDID transferred from the firmware.
 82          On the i386, this is from the Video BIOS. Enable this if DDC/I2C
 83          transfers do not work for your driver and if you are using
 84          nvidiafb, i810fb or savagefb.
 85 
 86          In general, choosing Y for this option is safe.  If you
 87          experience extremely long delays while booting before you get
 88          something on your display, try setting this to N.  Matrox cards in
 89          combination with certain motherboards and monitors are known to
 90          suffer from this problem.
 91 
 92 config FB_DDC
 93        tristate
 94        depends on FB
 95        select I2C_ALGOBIT
 96        select I2C
 97        default n
 98 
 99 config FB_BOOT_VESA_SUPPORT
100         bool
101         depends on FB
102         default n
103         ---help---
104           If true, at least one selected framebuffer driver can take advantage
105           of VESA video modes set at an early boot stage via the vga= parameter.
106 
107 config FB_CFB_FILLRECT
108         tristate
109         depends on FB
110         default n
111         ---help---
112           Include the cfb_fillrect function for generic software rectangle
113           filling. This is used by drivers that don't provide their own
114           (accelerated) version.
115 
116 config FB_CFB_COPYAREA
117         tristate
118         depends on FB
119         default n
120         ---help---
121           Include the cfb_copyarea function for generic software area copying.
122           This is used by drivers that don't provide their own (accelerated)
123           version.
124 
125 config FB_CFB_IMAGEBLIT
126         tristate
127         depends on FB
128         default n
129         ---help---
130           Include the cfb_imageblit function for generic software image
131           blitting. This is used by drivers that don't provide their own
132           (accelerated) version.
133 
134 config FB_CFB_REV_PIXELS_IN_BYTE
135         bool
136         depends on FB
137         default n
138         ---help---
139           Allow generic frame-buffer functions to work on displays with 1, 2
140           and 4 bits per pixel depths which has opposite order of pixels in
141           byte order to bytes in long order.
142 
143 config FB_SYS_FILLRECT
144         tristate
145         depends on FB
146         default n
147         ---help---
148           Include the sys_fillrect function for generic software rectangle
149           filling. This is used by drivers that don't provide their own
150           (accelerated) version and the framebuffer is in system RAM.
151 
152 config FB_SYS_COPYAREA
153         tristate
154         depends on FB
155         default n
156         ---help---
157           Include the sys_copyarea function for generic software area copying.
158           This is used by drivers that don't provide their own (accelerated)
159           version and the framebuffer is in system RAM.
160 
161 config FB_SYS_IMAGEBLIT
162         tristate
163         depends on FB
164         default n
165         ---help---
166           Include the sys_imageblit function for generic software image
167           blitting. This is used by drivers that don't provide their own
168           (accelerated) version and the framebuffer is in system RAM.
169 
170 menuconfig FB_FOREIGN_ENDIAN
171         bool "Framebuffer foreign endianness support"
172         depends on FB
173         ---help---
174           This menu will let you enable support for the framebuffers with
175           non-native endianness (e.g. Little-Endian framebuffer on a
176           Big-Endian machine). Most probably you don't have such hardware,
177           so it's safe to say "n" here.
178 
179 choice
180         prompt "Choice endianness support"
181         depends on FB_FOREIGN_ENDIAN
182 
183 config FB_BOTH_ENDIAN
184         bool "Support for Big- and Little-Endian framebuffers"
185 
186 config FB_BIG_ENDIAN
187         bool "Support for Big-Endian framebuffers only"
188 
189 config FB_LITTLE_ENDIAN
190         bool "Support for Little-Endian framebuffers only"
191 
192 endchoice
193 
194 config FB_SYS_FOPS
195        tristate
196        depends on FB
197        default n
198 
199 config FB_DEFERRED_IO
200         bool
201         depends on FB
202 
203 config FB_HECUBA
204         tristate
205         depends on FB
206         depends on FB_DEFERRED_IO
207 
208 config FB_SVGALIB
209         tristate
210         depends on FB
211         default n
212         ---help---
213           Common utility functions useful to fbdev drivers of VGA-based
214           cards.
215 
216 config FB_MACMODES
217        tristate
218        depends on FB
219        default n
220 
221 config FB_BACKLIGHT
222         bool
223         depends on FB
224         select BACKLIGHT_LCD_SUPPORT
225         select BACKLIGHT_CLASS_DEVICE
226         default n
227 
228 config FB_MODE_HELPERS
229         bool "Enable Video Mode Handling Helpers"
230         depends on FB
231         default n
232         ---help---
233           This enables functions for handling video modes using the
234           Generalized Timing Formula and the EDID parser. A few drivers rely
235           on this feature such as the radeonfb, rivafb, and the i810fb. If
236           your driver does not take advantage of this feature, choosing Y will
237           just increase the kernel size by about 5K.
238 
239 config FB_TILEBLITTING
240        bool "Enable Tile Blitting Support"
241        depends on FB
242        default n
243        ---help---
244          This enables tile blitting.  Tile blitting is a drawing technique
245          where the screen is divided into rectangular sections (tiles), whereas
246          the standard blitting divides the screen into pixels. Because the
247          default drawing element is a tile, drawing functions will be passed
248          parameters in terms of number of tiles instead of number of pixels.
249          For example, to draw a single character, instead of using bitmaps,
250          an index to an array of bitmaps will be used.  To clear or move a
251          rectangular section of a screen, the rectangle will be described in
252          terms of number of tiles in the x- and y-axis.
253 
254          This is particularly important to one driver, matroxfb.  If
255          unsure, say N.
256 
257 comment "Frame buffer hardware drivers"
258         depends on FB
259 
260 config FB_GRVGA
261         tristate "Aeroflex Gaisler framebuffer support"
262         depends on FB && SPARC
263         select FB_CFB_FILLRECT
264         select FB_CFB_COPYAREA
265         select FB_CFB_IMAGEBLIT
266         ---help---
267         This enables support for the SVGACTRL framebuffer in the GRLIB IP library from Aeroflex Gaisler.
268 
269 config FB_CIRRUS
270         tristate "Cirrus Logic support"
271         depends on FB && (ZORRO || PCI)
272         select FB_CFB_FILLRECT
273         select FB_CFB_COPYAREA
274         select FB_CFB_IMAGEBLIT
275         ---help---
276           This enables support for Cirrus Logic GD542x/543x based boards on
277           Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum.
278 
279           If you have a PCI-based system, this enables support for these
280           chips: GD-543x, GD-544x, GD-5480.
281 
282           Please read the file <file:Documentation/fb/cirrusfb.txt>.
283 
284           Say N unless you have such a graphics board or plan to get one
285           before you next recompile the kernel.
286 
287 config FB_PM2
288         tristate "Permedia2 support"
289         depends on FB && ((AMIGA && BROKEN) || PCI)
290         select FB_CFB_FILLRECT
291         select FB_CFB_COPYAREA
292         select FB_CFB_IMAGEBLIT
293         help
294           This is the frame buffer device driver for cards based on
295           the 3D Labs Permedia, Permedia 2 and Permedia 2V chips.
296           The driver was tested on the following cards:
297                 Diamond FireGL 1000 PRO AGP
298                 ELSA Gloria Synergy PCI
299                 Appian Jeronimo PRO (both heads) PCI
300                 3DLabs Oxygen ACX aka EONtronics Picasso P2 PCI
301                 Techsource Raptor GFX-8P (aka Sun PGX-32) on SPARC
302                 ASK Graphic Blaster Exxtreme AGP
303 
304           To compile this driver as a module, choose M here: the
305           module will be called pm2fb.
306 
307 config FB_PM2_FIFO_DISCONNECT
308         bool "enable FIFO disconnect feature"
309         depends on FB_PM2 && PCI
310         help
311           Support the Permedia2 FIFO disconnect feature.
312 
313 config FB_ARMCLCD
314         tristate "ARM PrimeCell PL110 support"
315         depends on ARM || ARM64 || COMPILE_TEST
316         depends on FB && ARM_AMBA
317         select FB_CFB_FILLRECT
318         select FB_CFB_COPYAREA
319         select FB_CFB_IMAGEBLIT
320         help
321           This framebuffer device driver is for the ARM PrimeCell PL110
322           Colour LCD controller.  ARM PrimeCells provide the building
323           blocks for System on a Chip devices.
324 
325           If you want to compile this as a module (=code which can be
326           inserted into and removed from the running kernel), say M
327           here and read <file:Documentation/kbuild/modules.txt>.  The module
328           will be called amba-clcd.
329 
330 config FB_ACORN
331         bool "Acorn VIDC support"
332         depends on (FB = y) && ARM && ARCH_ACORN
333         select FB_CFB_FILLRECT
334         select FB_CFB_COPYAREA
335         select FB_CFB_IMAGEBLIT
336         help
337           This is the frame buffer device driver for the Acorn VIDC graphics
338           hardware found in Acorn RISC PCs and other ARM-based machines.  If
339           unsure, say N.
340 
341 config FB_CLPS711X
342         bool "CLPS711X LCD support"
343         depends on (FB = y) && ARM && ARCH_CLPS711X
344         select FB_CFB_FILLRECT
345         select FB_CFB_COPYAREA
346         select FB_CFB_IMAGEBLIT
347         help
348           Say Y to enable the Framebuffer driver for the CLPS7111 and
349           EP7212 processors.
350 
351 config FB_SA1100
352         bool "SA-1100 LCD support"
353         depends on (FB = y) && ARM && ARCH_SA1100
354         select FB_CFB_FILLRECT
355         select FB_CFB_COPYAREA
356         select FB_CFB_IMAGEBLIT
357         help
358           This is a framebuffer device for the SA-1100 LCD Controller.
359           See <http://www.linux-fbdev.org/> for information on framebuffer
360           devices.
361 
362           If you plan to use the LCD display with your SA-1100 system, say
363           Y here.
364 
365 config FB_IMX
366         tristate "Freescale i.MX1/21/25/27 LCD support"
367         depends on FB && ARCH_MXC
368         select FB_CFB_FILLRECT
369         select FB_CFB_COPYAREA
370         select FB_CFB_IMAGEBLIT
371         select FB_MODE_HELPERS
372         select VIDEOMODE_HELPERS
373 
374 config FB_CYBER2000
375         tristate "CyberPro 2000/2010/5000 support"
376         depends on FB && PCI && (BROKEN || !SPARC64)
377         select FB_CFB_FILLRECT
378         select FB_CFB_COPYAREA
379         select FB_CFB_IMAGEBLIT
380         help
381           This enables support for the Integraphics CyberPro 20x0 and 5000
382           VGA chips used in the Rebel.com Netwinder and other machines.
383           Say Y if you have a NetWinder or a graphics card containing this
384           device, otherwise say N.
385 
386 config FB_CYBER2000_DDC
387         bool "DDC for CyberPro support"
388         depends on FB_CYBER2000
389         select FB_DDC
390         default y
391         help
392           Say Y here if you want DDC support for your CyberPro graphics
393           card. This is only I2C bus support, driver does not use EDID.
394 
395 config FB_CYBER2000_I2C
396         bool "CyberPro 2000/2010/5000 I2C support"
397         depends on FB_CYBER2000 && I2C && ARCH_NETWINDER
398         select I2C_ALGOBIT
399         help
400           Enable support for the I2C video decoder interface on the
401           Integraphics CyberPro 20x0 and 5000 VGA chips.  This is used
402           on the Netwinder machines for the SAA7111 video capture.
403 
404 config FB_APOLLO
405         bool
406         depends on (FB = y) && APOLLO
407         default y
408         select FB_CFB_FILLRECT
409         select FB_CFB_IMAGEBLIT
410 
411 config FB_Q40
412         bool
413         depends on (FB = y) && Q40
414         default y
415         select FB_CFB_FILLRECT
416         select FB_CFB_COPYAREA
417         select FB_CFB_IMAGEBLIT
418 
419 config FB_AMIGA
420         tristate "Amiga native chipset support"
421         depends on FB && AMIGA
422         help
423           This is the frame buffer device driver for the builtin graphics
424           chipset found in Amigas.
425 
426           To compile this driver as a module, choose M here: the
427           module will be called amifb.
428 
429 config FB_AMIGA_OCS
430         bool "Amiga OCS chipset support"
431         depends on FB_AMIGA
432         help
433           This enables support for the original Agnus and Denise video chips,
434           found in the Amiga 1000 and most A500's and A2000's. If you intend
435           to run Linux on any of these systems, say Y; otherwise say N.
436 
437 config FB_AMIGA_ECS
438         bool "Amiga ECS chipset support"
439         depends on FB_AMIGA
440         help
441           This enables support for the Enhanced Chip Set, found in later
442           A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If
443           you intend to run Linux on any of these systems, say Y; otherwise
444           say N.
445 
446 config FB_AMIGA_AGA
447         bool "Amiga AGA chipset support"
448         depends on FB_AMIGA
449         help
450           This enables support for the Advanced Graphics Architecture (also
451           known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T
452           and CD32. If you intend to run Linux on any of these systems, say Y;
453           otherwise say N.
454 
455 config FB_FM2
456         bool "Amiga FrameMaster II/Rainbow II support"
457         depends on (FB = y) && ZORRO
458         select FB_CFB_FILLRECT
459         select FB_CFB_COPYAREA
460         select FB_CFB_IMAGEBLIT
461         help
462           This is the frame buffer device driver for the Amiga FrameMaster
463           card from BSC (exhibited 1992 but not shipped as a CBM product).
464 
465 config FB_ARC
466         tristate "Arc Monochrome LCD board support"
467         depends on FB && X86
468         select FB_SYS_FILLRECT
469         select FB_SYS_COPYAREA
470         select FB_SYS_IMAGEBLIT
471         select FB_SYS_FOPS
472         help
473           This enables support for the Arc Monochrome LCD board. The board
474           is based on the KS-108 lcd controller and is typically a matrix
475           of 2*n chips. This driver was tested with a 128x64 panel. This
476           driver supports it for use with x86 SBCs through a 16 bit GPIO
477           interface (8 bit data, 8 bit control). If you anticipate using
478           this driver, say Y or M; otherwise say N. You must specify the
479           GPIO IO address to be used for setting control and data.
480 
481 config FB_ATARI
482         bool "Atari native chipset support"
483         depends on (FB = y) && ATARI
484         select FB_CFB_FILLRECT
485         select FB_CFB_COPYAREA
486         select FB_CFB_IMAGEBLIT
487         help
488           This is the frame buffer device driver for the builtin graphics
489           chipset found in Ataris.
490 
491 config FB_OF
492         bool "Open Firmware frame buffer device support"
493         depends on (FB = y) && (PPC64 || PPC_OF) && (!PPC_PSERIES || PCI)
494         select FB_CFB_FILLRECT
495         select FB_CFB_COPYAREA
496         select FB_CFB_IMAGEBLIT
497         select FB_MACMODES
498         help
499           Say Y if you want support with Open Firmware for your graphics
500           board.
501 
502 config FB_CONTROL
503         bool "Apple \"control\" display support"
504         depends on (FB = y) && PPC_PMAC && PPC32
505         select FB_CFB_FILLRECT
506         select FB_CFB_COPYAREA
507         select FB_CFB_IMAGEBLIT
508         select FB_MACMODES
509         help
510           This driver supports a frame buffer for the graphics adapter in the
511           Power Macintosh 7300 and others.
512 
513 config FB_PLATINUM
514         bool "Apple \"platinum\" display support"
515         depends on (FB = y) && PPC_PMAC && PPC32
516         select FB_CFB_FILLRECT
517         select FB_CFB_COPYAREA
518         select FB_CFB_IMAGEBLIT
519         select FB_MACMODES
520         help
521           This driver supports a frame buffer for the "platinum" graphics
522           adapter in some Power Macintoshes.
523 
524 config FB_VALKYRIE
525         bool "Apple \"valkyrie\" display support"
526         depends on (FB = y) && (MAC || (PPC_PMAC && PPC32))
527         select FB_CFB_FILLRECT
528         select FB_CFB_COPYAREA
529         select FB_CFB_IMAGEBLIT
530         select FB_MACMODES
531         help
532           This driver supports a frame buffer for the "valkyrie" graphics
533           adapter in some Power Macintoshes.
534 
535 config FB_CT65550
536         bool "Chips 65550 display support"
537         depends on (FB = y) && PPC32 && PCI
538         select FB_CFB_FILLRECT
539         select FB_CFB_COPYAREA
540         select FB_CFB_IMAGEBLIT
541         help
542           This is the frame buffer device driver for the Chips & Technologies
543           65550 graphics chip in PowerBooks.
544 
545 config FB_ASILIANT
546         bool "Asiliant (Chips) 69000 display support"
547         depends on (FB = y) && PCI
548         select FB_CFB_FILLRECT
549         select FB_CFB_COPYAREA
550         select FB_CFB_IMAGEBLIT
551         help
552           This is the frame buffer device driver for the Asiliant 69030 chipset
553 
554 config FB_IMSTT
555         bool "IMS Twin Turbo display support"
556         depends on (FB = y) && PCI
557         select FB_CFB_IMAGEBLIT
558         select FB_MACMODES if PPC
559         help
560           The IMS Twin Turbo is a PCI-based frame buffer card bundled with
561           many Macintosh and compatible computers.
562 
563 config FB_VGA16
564         tristate "VGA 16-color graphics support"
565         depends on FB && (X86 || PPC)
566         select FB_CFB_FILLRECT
567         select FB_CFB_COPYAREA
568         select FB_CFB_IMAGEBLIT
569         select VGASTATE
570         select FONT_8x16 if FRAMEBUFFER_CONSOLE
571         help
572           This is the frame buffer device driver for VGA 16 color graphic
573           cards. Say Y if you have such a card.
574 
575           To compile this driver as a module, choose M here: the
576           module will be called vga16fb.
577 
578 config FB_BF54X_LQ043
579         tristate "SHARP LQ043 TFT LCD (BF548 EZKIT)"
580         depends on FB && (BF54x) && !BF542
581         select FB_CFB_FILLRECT
582         select FB_CFB_COPYAREA
583         select FB_CFB_IMAGEBLIT
584         help
585          This is the framebuffer device driver for a SHARP LQ043T1DG01 TFT LCD
586 
587 config FB_BFIN_T350MCQB
588         tristate "Varitronix COG-T350MCQB TFT LCD display (BF527 EZKIT)"
589         depends on FB && BLACKFIN
590         select BFIN_GPTIMERS
591         select FB_CFB_FILLRECT
592         select FB_CFB_COPYAREA
593         select FB_CFB_IMAGEBLIT
594         help
595          This is the framebuffer device driver for a Varitronix VL-PS-COG-T350MCQB-01 display TFT LCD
596          This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI
597          It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK.
598 
599 config FB_BFIN_LQ035Q1
600         tristate "SHARP LQ035Q1DH02 TFT LCD"
601         depends on FB && BLACKFIN && SPI
602         select FB_CFB_FILLRECT
603         select FB_CFB_COPYAREA
604         select FB_CFB_IMAGEBLIT
605         select BFIN_GPTIMERS
606         help
607           This is the framebuffer device driver for a SHARP LQ035Q1DH02 TFT display found on
608           the Blackfin Landscape LCD EZ-Extender Card.
609           This display is a QVGA 320x240 18-bit RGB display interfaced by an 16-bit wide PPI
610           It uses PPI[0..15] PPI_FS1, PPI_FS2 and PPI_CLK.
611 
612           To compile this driver as a module, choose M here: the
613           module will be called bfin-lq035q1-fb.
614 
615 config FB_BF537_LQ035
616         tristate "SHARP LQ035 TFT LCD (BF537 STAMP)"
617         depends on FB && (BF534 || BF536 || BF537) && I2C_BLACKFIN_TWI
618         select FB_CFB_FILLRECT
619         select FB_CFB_COPYAREA
620         select FB_CFB_IMAGEBLIT
621         select BFIN_GPTIMERS
622         help
623           This is the framebuffer device for a SHARP LQ035Q7DB03 TFT LCD
624           attached to a BF537.
625 
626           To compile this driver as a module, choose M here: the
627           module will be called bf537-lq035.
628 
629 config FB_BFIN_7393
630         tristate "Blackfin ADV7393 Video encoder"
631         depends on FB && BLACKFIN
632         select I2C
633         select FB_CFB_FILLRECT
634         select FB_CFB_COPYAREA
635         select FB_CFB_IMAGEBLIT
636         help
637           This is the framebuffer device for a ADV7393 video encoder
638           attached to a Blackfin on the PPI port.
639           If your Blackfin board has a ADV7393 select Y.
640 
641           To compile this driver as a module, choose M here: the
642           module will be called bfin_adv7393fb.
643 
644 choice
645         prompt  "Video mode support"
646         depends on FB_BFIN_7393
647         default NTSC
648 
649 config NTSC
650         bool 'NTSC 720x480'
651 
652 config PAL
653         bool 'PAL 720x576'
654 
655 config NTSC_640x480
656         bool 'NTSC 640x480 (Experimental)'
657 
658 config PAL_640x480
659         bool 'PAL 640x480 (Experimental)'
660 
661 config NTSC_YCBCR
662         bool 'NTSC 720x480 YCbCR input'
663 
664 config PAL_YCBCR
665         bool 'PAL 720x576 YCbCR input'
666 
667 endchoice
668 
669 choice
670         prompt  "Size of ADV7393 frame buffer memory Single/Double Size"
671         depends on (FB_BFIN_7393)
672         default ADV7393_1XMEM
673 
674 config ADV7393_1XMEM
675         bool 'Single'
676 
677 config ADV7393_2XMEM
678         bool 'Double'
679 endchoice
680 
681 config FB_STI
682         tristate "HP STI frame buffer device support"
683         depends on FB && PARISC
684         select FB_CFB_FILLRECT
685         select FB_CFB_COPYAREA
686         select FB_CFB_IMAGEBLIT
687         select STI_CONSOLE
688         select VT
689         default y
690         ---help---
691           STI refers to the HP "Standard Text Interface" which is a set of
692           BIOS routines contained in a ROM chip in HP PA-RISC based machines.
693           Enabling this option will implement the linux framebuffer device
694           using calls to the STI BIOS routines for initialisation.
695         
696           If you enable this option, you will get a planar framebuffer device
697           /dev/fb which will work on the most common HP graphic cards of the
698           NGLE family, including the artist chips (in the 7xx and Bxxx series),
699           HCRX, HCRX24, CRX, CRX24 and VisEG series.
700 
701           It is safe to enable this option, so you should probably say "Y".
702 
703 config FB_MAC
704         bool "Generic Macintosh display support"
705         depends on (FB = y) && MAC
706         select FB_CFB_FILLRECT
707         select FB_CFB_COPYAREA
708         select FB_CFB_IMAGEBLIT
709         select FB_MACMODES
710 
711 config FB_HP300
712         bool
713         depends on (FB = y) && DIO
714         select FB_CFB_IMAGEBLIT
715         default y
716 
717 config FB_TGA
718         tristate "TGA/SFB+ framebuffer support"
719         depends on FB && (ALPHA || TC)
720         select FB_CFB_FILLRECT
721         select FB_CFB_COPYAREA
722         select FB_CFB_IMAGEBLIT
723         select BITREVERSE
724         ---help---
725           This is the frame buffer device driver for generic TGA and SFB+
726           graphic cards.  These include DEC ZLXp-E1, -E2 and -E3 PCI cards,
727           also known as PBXGA-A, -B and -C, and DEC ZLX-E1, -E2 and -E3
728           TURBOchannel cards, also known as PMAGD-A, -B and -C.
729 
730           Due to hardware limitations ZLX-E2 and E3 cards are not supported
731           for DECstation 5000/200 systems.  Additionally due to firmware
732           limitations these cards may cause troubles with booting DECstation
733           5000/240 and /260 systems, but are fully supported under Linux if
734           you manage to get it going. ;-)
735 
736           Say Y if you have one of those.
737 
738 config FB_UVESA
739         tristate "Userspace VESA VGA graphics support"
740         depends on FB && CONNECTOR
741         select FB_CFB_FILLRECT
742         select FB_CFB_COPYAREA
743         select FB_CFB_IMAGEBLIT
744         select FB_MODE_HELPERS
745         help
746           This is the frame buffer driver for generic VBE 2.0 compliant
747           graphic cards. It can also take advantage of VBE 3.0 features,
748           such as refresh rate adjustment.
749 
750           This driver generally provides more features than vesafb but
751           requires a userspace helper application called 'v86d'. See
752           <file:Documentation/fb/uvesafb.txt> for more information.
753 
754           If unsure, say N.
755 
756 config FB_VESA
757         bool "VESA VGA graphics support"
758         depends on (FB = y) && X86
759         select FB_CFB_FILLRECT
760         select FB_CFB_COPYAREA
761         select FB_CFB_IMAGEBLIT
762         select FB_BOOT_VESA_SUPPORT
763         help
764           This is the frame buffer device driver for generic VESA 2.0
765           compliant graphic cards. The older VESA 1.2 cards are not supported.
766           You will get a boot time penguin logo at no additional cost. Please
767           read <file:Documentation/fb/vesafb.txt>. If unsure, say Y.
768 
769 config FB_EFI
770         bool "EFI-based Framebuffer Support"
771         depends on (FB = y) && X86 && EFI
772         select FB_CFB_FILLRECT
773         select FB_CFB_COPYAREA
774         select FB_CFB_IMAGEBLIT
775         help
776           This is the EFI frame buffer device driver. If the firmware on
777           your platform is EFI 1.10 or UEFI 2.0, select Y to add support for
778           using the EFI framebuffer as your console.
779 
780 config FB_N411
781        tristate "N411 Apollo/Hecuba devkit support"
782        depends on FB && X86 && MMU
783        select FB_SYS_FILLRECT
784        select FB_SYS_COPYAREA
785        select FB_SYS_IMAGEBLIT
786        select FB_SYS_FOPS
787        select FB_DEFERRED_IO
788        select FB_HECUBA
789        help
790          This enables support for the Apollo display controller in its
791          Hecuba form using the n411 devkit.
792 
793 config FB_HGA
794         tristate "Hercules mono graphics support"
795         depends on FB && X86
796         help
797           Say Y here if you have a Hercules mono graphics card.
798 
799           To compile this driver as a module, choose M here: the
800           module will be called hgafb.
801 
802           As this card technology is at least 25 years old,
803           most people will answer N here.
804 
805 config FB_SGIVW
806         tristate "SGI Visual Workstation framebuffer support"
807         depends on FB && X86_VISWS
808         select FB_CFB_FILLRECT
809         select FB_CFB_COPYAREA
810         select FB_CFB_IMAGEBLIT
811         help
812           SGI Visual Workstation support for framebuffer graphics.
813 
814 config FB_GBE
815         bool "SGI Graphics Backend frame buffer support"
816         depends on (FB = y) && (SGI_IP32 || X86_VISWS)
817         select FB_CFB_FILLRECT
818         select FB_CFB_COPYAREA
819         select FB_CFB_IMAGEBLIT
820         help
821           This is the frame buffer device driver for SGI Graphics Backend.
822           This chip is used in SGI O2 and Visual Workstation 320/540.
823 
824 config FB_GBE_MEM
825         int "Video memory size in MB"
826         depends on FB_GBE
827         default 4
828         help
829           This is the amount of memory reserved for the framebuffer,
830           which can be any value between 1MB and 8MB.
831 
832 config FB_SBUS
833         bool "SBUS and UPA framebuffers"
834         depends on (FB = y) && SPARC
835         help
836           Say Y if you want support for SBUS or UPA based frame buffer device.
837 
838 config FB_BW2
839         bool "BWtwo support"
840         depends on (FB = y) && (SPARC && FB_SBUS)
841         select FB_CFB_FILLRECT
842         select FB_CFB_COPYAREA
843         select FB_CFB_IMAGEBLIT
844         help
845           This is the frame buffer device driver for the BWtwo frame buffer.
846 
847 config FB_CG3
848         bool "CGthree support"
849         depends on (FB = y) && (SPARC && FB_SBUS)
850         select FB_CFB_FILLRECT
851         select FB_CFB_COPYAREA
852         select FB_CFB_IMAGEBLIT
853         help
854           This is the frame buffer device driver for the CGthree frame buffer.
855 
856 config FB_CG6
857         bool "CGsix (GX,TurboGX) support"
858         depends on (FB = y) && (SPARC && FB_SBUS)
859         select FB_CFB_COPYAREA
860         select FB_CFB_IMAGEBLIT
861         help
862           This is the frame buffer device driver for the CGsix (GX, TurboGX)
863           frame buffer.
864 
865 config FB_FFB
866         bool "Creator/Creator3D/Elite3D support"
867         depends on FB_SBUS && SPARC64
868         select FB_CFB_COPYAREA
869         select FB_CFB_IMAGEBLIT
870         help
871           This is the frame buffer device driver for the Creator, Creator3D,
872           and Elite3D graphics boards.
873 
874 config FB_TCX
875         bool "TCX (SS4/SS5 only) support"
876         depends on FB_SBUS
877         select FB_CFB_FILLRECT
878         select FB_CFB_COPYAREA
879         select FB_CFB_IMAGEBLIT
880         help
881           This is the frame buffer device driver for the TCX 24/8bit frame
882           buffer.
883 
884 config FB_CG14
885         bool "CGfourteen (SX) support"
886         depends on FB_SBUS
887         select FB_CFB_FILLRECT
888         select FB_CFB_COPYAREA
889         select FB_CFB_IMAGEBLIT
890         help
891           This is the frame buffer device driver for the CGfourteen frame
892           buffer on Desktop SPARCsystems with the SX graphics option.
893 
894 config FB_P9100
895         bool "P9100 (Sparcbook 3 only) support"
896         depends on FB_SBUS
897         select FB_CFB_FILLRECT
898         select FB_CFB_COPYAREA
899         select FB_CFB_IMAGEBLIT
900         help
901           This is the frame buffer device driver for the P9100 card
902           supported on Sparcbook 3 machines.
903 
904 config FB_LEO
905         bool "Leo (ZX) support"
906         depends on FB_SBUS
907         select FB_CFB_FILLRECT
908         select FB_CFB_COPYAREA
909         select FB_CFB_IMAGEBLIT
910         help
911           This is the frame buffer device driver for the SBUS-based Sun ZX
912           (leo) frame buffer cards.
913 
914 config FB_IGA
915         bool "IGA 168x display support"
916         depends on (FB = y) && SPARC32
917         select FB_CFB_FILLRECT
918         select FB_CFB_COPYAREA
919         select FB_CFB_IMAGEBLIT
920         help
921           This is the framebuffer device for the INTERGRAPHICS 1680 and
922           successor frame buffer cards.
923 
924 config FB_XVR500
925         bool "Sun XVR-500 3DLABS Wildcat support"
926         depends on (FB = y) && PCI && SPARC64
927         select FB_CFB_FILLRECT
928         select FB_CFB_COPYAREA
929         select FB_CFB_IMAGEBLIT
930         help
931           This is the framebuffer device for the Sun XVR-500 and similar
932           graphics cards based upon the 3DLABS Wildcat chipset.  The driver
933           only works on sparc64 systems where the system firmware has
934           mostly initialized the card already.  It is treated as a
935           completely dumb framebuffer device.
936 
937 config FB_XVR2500
938         bool "Sun XVR-2500 3DLABS Wildcat support"
939         depends on (FB = y) && PCI && SPARC64
940         select FB_CFB_FILLRECT
941         select FB_CFB_COPYAREA
942         select FB_CFB_IMAGEBLIT
943         help
944           This is the framebuffer device for the Sun XVR-2500 and similar
945           graphics cards based upon the 3DLABS Wildcat chipset.  The driver
946           only works on sparc64 systems where the system firmware has
947           mostly initialized the card already.  It is treated as a
948           completely dumb framebuffer device.
949 
950 config FB_XVR1000
951         bool "Sun XVR-1000 support"
952         depends on (FB = y) && SPARC64
953         select FB_CFB_FILLRECT
954         select FB_CFB_COPYAREA
955         select FB_CFB_IMAGEBLIT
956         help
957           This is the framebuffer device for the Sun XVR-1000 and similar
958           graphics cards.  The driver only works on sparc64 systems where
959           the system firmware has mostly initialized the card already.  It
960           is treated as a completely dumb framebuffer device.
961 
962 config FB_PVR2
963         tristate "NEC PowerVR 2 display support"
964         depends on FB && SH_DREAMCAST
965         select FB_CFB_FILLRECT
966         select FB_CFB_COPYAREA
967         select FB_CFB_IMAGEBLIT
968         ---help---
969           Say Y here if you have a PowerVR 2 card in your box.  If you plan to
970           run linux on your Dreamcast, you will have to say Y here.
971           This driver may or may not work on other PowerVR 2 cards, but is
972           totally untested.  Use at your own risk.  If unsure, say N.
973 
974           To compile this driver as a module, choose M here: the
975           module will be called pvr2fb.
976 
977           You can pass several parameters to the driver at boot time or at
978           module load time.  The parameters look like "video=pvr2:XXX", where
979           the meaning of XXX can be found at the end of the main source file
980           (<file:drivers/video/pvr2fb.c>). Please see the file
981           <file:Documentation/fb/pvr2fb.txt>.
982 
983 config FB_OPENCORES
984         tristate "OpenCores VGA/LCD core 2.0 framebuffer support"
985         depends on FB
986         select FB_CFB_FILLRECT
987         select FB_CFB_COPYAREA
988         select FB_CFB_IMAGEBLIT
989         help
990           This enables support for the OpenCores VGA/LCD core.
991 
992           The OpenCores VGA/LCD core is typically used together with
993           softcore CPUs (e.g. OpenRISC or Microblaze) or hard processor
994           systems (e.g. Altera socfpga or Xilinx Zynq) on FPGAs.
995 
996           The source code and specification for the core is available at
997           <http://opencores.org/project,vga_lcd>
998 
999 config FB_S1D13XXX
1000         tristate "Epson S1D13XXX framebuffer support"
1001         depends on FB
1002         select FB_CFB_FILLRECT
1003         select FB_CFB_COPYAREA
1004         select FB_CFB_IMAGEBLIT
1005         help
1006           Support for S1D13XXX framebuffer device family (currently only
1007           working with S1D13806). Product specs at
1008           <http://vdc.epson.com/>
1009 
1010 config FB_ATMEL
1011         tristate "AT91/AT32 LCD Controller support"
1012         depends on FB && HAVE_FB_ATMEL
1013         select FB_CFB_FILLRECT
1014         select FB_CFB_COPYAREA
1015         select FB_CFB_IMAGEBLIT
1016         select FB_MODE_HELPERS
1017         select VIDEOMODE_HELPERS
1018         help
1019           This enables support for the AT91/AT32 LCD Controller.
1020 
1021 config FB_INTSRAM
1022         bool "Frame Buffer in internal SRAM"
1023         depends on FB_ATMEL && ARCH_AT91SAM9261
1024         help
1025           Say Y if you want to map Frame Buffer in internal SRAM. Say N if you want
1026           to let frame buffer in external SDRAM.
1027 
1028 config FB_ATMEL_STN
1029         bool "Use a STN display with AT91/AT32 LCD Controller"
1030         depends on FB_ATMEL && (MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK)
1031         default n
1032         help
1033           Say Y if you want to connect a STN LCD display to the AT91/AT32 LCD
1034           Controller. Say N if you want to connect a TFT.
1035 
1036           If unsure, say N.
1037 
1038 config FB_NVIDIA
1039         tristate "nVidia Framebuffer Support"
1040         depends on FB && PCI
1041         select FB_BACKLIGHT if FB_NVIDIA_BACKLIGHT
1042         select FB_MODE_HELPERS
1043         select FB_CFB_FILLRECT
1044         select FB_CFB_COPYAREA
1045         select FB_CFB_IMAGEBLIT
1046         select BITREVERSE
1047         select VGASTATE
1048         help
1049           This driver supports graphics boards with the nVidia chips, TNT
1050           and newer. For very old chipsets, such as the RIVA128, then use
1051           the rivafb.
1052           Say Y if you have such a graphics board.
1053 
1054           To compile this driver as a module, choose M here: the
1055           module will be called nvidiafb.
1056 
1057 config FB_NVIDIA_I2C
1058        bool "Enable DDC Support"
1059        depends on FB_NVIDIA
1060        select FB_DDC
1061        help
1062           This enables I2C support for nVidia Chipsets.  This is used
1063           only for getting EDID information from the attached display
1064           allowing for robust video mode handling and switching.
1065 
1066           Because fbdev-2.6 requires that drivers must be able to
1067           independently validate video mode parameters, you should say Y
1068           here.
1069 
1070 config FB_NVIDIA_DEBUG
1071         bool "Lots of debug output"
1072         depends on FB_NVIDIA
1073         default n
1074         help
1075           Say Y here if you want the nVidia driver to output all sorts
1076           of debugging information to provide to the maintainer when
1077           something goes wrong.
1078 
1079 config FB_NVIDIA_BACKLIGHT
1080         bool "Support for backlight control"
1081         depends on FB_NVIDIA
1082         default y
1083         help
1084           Say Y here if you want to control the backlight of your display.
1085 
1086 config FB_RIVA
1087         tristate "nVidia Riva support"
1088         depends on FB && PCI
1089         select FB_BACKLIGHT if FB_RIVA_BACKLIGHT
1090         select FB_MODE_HELPERS
1091         select FB_CFB_FILLRECT
1092         select FB_CFB_COPYAREA
1093         select FB_CFB_IMAGEBLIT
1094         select BITREVERSE
1095         select VGASTATE
1096         help
1097           This driver supports graphics boards with the nVidia Riva/Geforce
1098           chips.
1099           Say Y if you have such a graphics board.
1100 
1101           To compile this driver as a module, choose M here: the
1102           module will be called rivafb.
1103 
1104 config FB_RIVA_I2C
1105        bool "Enable DDC Support"
1106        depends on FB_RIVA
1107        select FB_DDC
1108        help
1109           This enables I2C support for nVidia Chipsets.  This is used
1110           only for getting EDID information from the attached display
1111           allowing for robust video mode handling and switching.
1112 
1113           Because fbdev-2.6 requires that drivers must be able to
1114           independently validate video mode parameters, you should say Y
1115           here.
1116 
1117 config FB_RIVA_DEBUG
1118         bool "Lots of debug output"
1119         depends on FB_RIVA
1120         default n
1121         help
1122           Say Y here if you want the Riva driver to output all sorts
1123           of debugging information to provide to the maintainer when
1124           something goes wrong.
1125 
1126 config FB_RIVA_BACKLIGHT
1127         bool "Support for backlight control"
1128         depends on FB_RIVA
1129         default y
1130         help
1131           Say Y here if you want to control the backlight of your display.
1132 
1133 config FB_I740
1134         tristate "Intel740 support"
1135         depends on FB && PCI
1136         select FB_MODE_HELPERS
1137         select FB_CFB_FILLRECT
1138         select FB_CFB_COPYAREA
1139         select FB_CFB_IMAGEBLIT
1140         select VGASTATE
1141         select FB_DDC
1142         help
1143           This driver supports graphics cards based on Intel740 chip.
1144 
1145 config FB_I810
1146         tristate "Intel 810/815 support"
1147         depends on FB && PCI && X86_32 && AGP_INTEL
1148         select FB_MODE_HELPERS
1149         select FB_CFB_FILLRECT
1150         select FB_CFB_COPYAREA
1151         select FB_CFB_IMAGEBLIT
1152         select VGASTATE
1153         help
1154           This driver supports the on-board graphics built in to the Intel 810 
1155           and 815 chipsets.  Say Y if you have and plan to use such a board.
1156 
1157           To compile this driver as a module, choose M here: the
1158           module will be called i810fb.
1159 
1160           For more information, please read 
1161           <file:Documentation/fb/intel810.txt>
1162 
1163 config FB_I810_GTF
1164         bool "use VESA Generalized Timing Formula"
1165         depends on FB_I810
1166         help
1167           If you say Y, then the VESA standard, Generalized Timing Formula 
1168           or GTF, will be used to calculate the required video timing values
1169           per video mode.  Since the GTF allows nondiscrete timings 
1170           (nondiscrete being a range of values as opposed to discrete being a
1171           set of values), you'll be able to use any combination of horizontal 
1172           and vertical resolutions, and vertical refresh rates without having
1173           to specify your own timing parameters.  This is especially useful
1174           to maximize the performance of an aging display, or if you just 
1175           have a display with nonstandard dimensions. A VESA compliant 
1176           monitor is recommended, but can still work with non-compliant ones.
1177           If you need or want this, then select this option. The timings may 
1178           not be compliant with Intel's recommended values. Use at your own 
1179           risk.
1180 
1181           If you say N, the driver will revert to discrete video timings 
1182           using a set recommended by Intel in their documentation.
1183   
1184           If unsure, say N.
1185 
1186 config FB_I810_I2C
1187         bool "Enable DDC Support"
1188         depends on FB_I810 && FB_I810_GTF
1189         select FB_DDC
1190         help
1191 
1192 config FB_LE80578
1193         tristate "Intel LE80578 (Vermilion) support"
1194         depends on FB && PCI && X86
1195         select FB_MODE_HELPERS
1196         select FB_CFB_FILLRECT
1197         select FB_CFB_COPYAREA
1198         select FB_CFB_IMAGEBLIT
1199         help
1200           This driver supports the LE80578 (Vermilion Range) chipset
1201 
1202 config FB_CARILLO_RANCH
1203         tristate "Intel Carillo Ranch support"
1204         depends on FB_LE80578 && FB && PCI && X86
1205         help
1206           This driver supports the LE80578 (Carillo Ranch) board
1207 
1208 config FB_INTEL
1209         tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support"
1210         depends on FB && PCI && X86 && AGP_INTEL && EXPERT
1211         select FB_MODE_HELPERS
1212         select FB_CFB_FILLRECT
1213         select FB_CFB_COPYAREA
1214         select FB_CFB_IMAGEBLIT
1215         select FB_BOOT_VESA_SUPPORT if FB_INTEL = y
1216         depends on !DRM_I915
1217         help
1218           This driver supports the on-board graphics built in to the Intel
1219           830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets.
1220           Say Y if you have and plan to use such a board.
1221 
1222           To make FB_INTELFB=Y work you need to say AGP_INTEL=y too.
1223 
1224           To compile this driver as a module, choose M here: the
1225           module will be called intelfb.
1226 
1227           For more information, please read <file:Documentation/fb/intelfb.txt>
1228 
1229 config FB_INTEL_DEBUG
1230         bool "Intel driver Debug Messages"
1231         depends on FB_INTEL
1232         ---help---
1233           Say Y here if you want the Intel driver to output all sorts
1234           of debugging information to provide to the maintainer when
1235           something goes wrong.
1236 
1237 config FB_INTEL_I2C
1238         bool "DDC/I2C for Intel framebuffer support"
1239         depends on FB_INTEL
1240         select FB_DDC
1241         default y
1242         help
1243           Say Y here if you want DDC/I2C support for your on-board Intel graphics.
1244 
1245 config FB_MATROX
1246         tristate "Matrox acceleration"
1247         depends on FB && PCI
1248         select FB_CFB_FILLRECT
1249         select FB_CFB_COPYAREA
1250         select FB_CFB_IMAGEBLIT
1251         select FB_TILEBLITTING
1252         select FB_MACMODES if PPC_PMAC
1253         ---help---
1254           Say Y here if you have a Matrox Millennium, Matrox Millennium II,
1255           Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox
1256           Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video,
1257           Matrox G400, G450 or G550 card in your box.
1258 
1259           To compile this driver as a module, choose M here: the
1260           module will be called matroxfb.
1261 
1262           You can pass several parameters to the driver at boot time or at
1263           module load time. The parameters look like "video=matroxfb:XXX", and
1264           are described in <file:Documentation/fb/matroxfb.txt>.
1265 
1266 config FB_MATROX_MILLENIUM
1267         bool "Millennium I/II support"
1268         depends on FB_MATROX
1269         help
1270           Say Y here if you have a Matrox Millennium or Matrox Millennium II
1271           video card. If you select "Advanced lowlevel driver options" below,
1272           you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp
1273           packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can
1274           also use font widths different from 8.
1275 
1276 config FB_MATROX_MYSTIQUE
1277         bool "Mystique support"
1278         depends on FB_MATROX
1279         help
1280           Say Y here if you have a Matrox Mystique or Matrox Mystique 220
1281           video card. If you select "Advanced lowlevel driver options" below,
1282           you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp
1283           packed pixel and 32 bpp packed pixel. You can also use font widths
1284           different from 8.
1285 
1286 config FB_MATROX_G
1287         bool "G100/G200/G400/G450/G550 support"
1288         depends on FB_MATROX
1289         ---help---
1290           Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based
1291           video card. If you select "Advanced lowlevel driver options", you
1292           should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed
1293           pixel and 32 bpp packed pixel. You can also use font widths
1294           different from 8.
1295 
1296           If you need support for G400 secondary head, you must say Y to
1297           "Matrox I2C support" and "G400 second head support" right below.
1298           G450/G550 secondary head and digital output are supported without
1299           additional modules.
1300 
1301           The driver starts in monitor mode. You must use the matroxset tool 
1302           (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to 
1303           swap primary and secondary head outputs, or to change output mode.  
1304           Secondary head driver always start in 640x480 resolution and you 
1305           must use fbset to change it.
1306 
1307           Do not forget that second head supports only 16 and 32 bpp
1308           packed pixels, so it is a good idea to compile them into the kernel
1309           too. You can use only some font widths, as the driver uses generic
1310           painting procedures (the secondary head does not use acceleration
1311           engine).
1312 
1313           G450/G550 hardware can display TV picture only from secondary CRTC,
1314           and it performs no scaling, so picture must have 525 or 625 lines.
1315 
1316 config FB_MATROX_I2C
1317         tristate "Matrox I2C support"
1318         depends on FB_MATROX
1319         select FB_DDC
1320         ---help---
1321           This drivers creates I2C buses which are needed for accessing the
1322           DDC (I2C) bus present on all Matroxes, an I2C bus which
1323           interconnects Matrox optional devices, like MGA-TVO on G200 and
1324           G400, and the secondary head DDC bus, present on G400 only.
1325 
1326           You can say Y or M here if you want to experiment with monitor
1327           detection code. You must say Y or M here if you want to use either
1328           second head of G400 or MGA-TVO on G200 or G400.
1329 
1330           If you compile it as module, it will create a module named
1331           i2c-matroxfb.
1332 
1333 config FB_MATROX_MAVEN
1334         tristate "G400 second head support"
1335         depends on FB_MATROX_G && FB_MATROX_I2C
1336         ---help---
1337           WARNING !!! This support does not work with G450 !!!
1338 
1339           Say Y or M here if you want to use a secondary head (meaning two
1340           monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary
1341           head is not compatible with accelerated XFree 3.3.x SVGA servers -
1342           secondary head output is blanked while you are in X. With XFree
1343           3.9.17 preview you can use both heads if you use SVGA over fbdev or
1344           the fbdev driver on first head and the fbdev driver on second head.
1345 
1346           If you compile it as module, two modules are created,
1347           matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for
1348           both G200 and G400, matroxfb_crtc2 is needed only by G400. You must
1349           also load i2c-matroxfb to get it to run.
1350 
1351           The driver starts in monitor mode and you must use the matroxset
1352           tool (available at
1353           <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to
1354           PAL or NTSC or to swap primary and secondary head outputs.
1355           Secondary head driver also always start in 640x480 resolution, you
1356           must use fbset to change it.
1357 
1358           Also do not forget that second head supports only 16 and 32 bpp
1359           packed pixels, so it is a good idea to compile them into the kernel
1360           too.  You can use only some font widths, as the driver uses generic
1361           painting procedures (the secondary head does not use acceleration
1362           engine).
1363 
1364 config FB_RADEON
1365         tristate "ATI Radeon display support"
1366         depends on FB && PCI
1367         select FB_BACKLIGHT if FB_RADEON_BACKLIGHT
1368         select FB_MODE_HELPERS
1369         select FB_CFB_FILLRECT
1370         select FB_CFB_COPYAREA
1371         select FB_CFB_IMAGEBLIT
1372         select FB_MACMODES if PPC_OF
1373         help
1374           Choose this option if you want to use an ATI Radeon graphics card as
1375           a framebuffer device.  There are both PCI and AGP versions.  You
1376           don't need to choose this to run the Radeon in plain VGA mode.
1377 
1378           There is a product page at
1379           http://products.amd.com/en-us/GraphicCardResult.aspx
1380 
1381 config FB_RADEON_I2C
1382         bool "DDC/I2C for ATI Radeon support"
1383         depends on FB_RADEON
1384         select FB_DDC
1385         default y
1386         help
1387           Say Y here if you want DDC/I2C support for your Radeon board. 
1388 
1389 config FB_RADEON_BACKLIGHT
1390         bool "Support for backlight control"
1391         depends on FB_RADEON
1392         default y
1393         help
1394           Say Y here if you want to control the backlight of your display.
1395 
1396 config FB_RADEON_DEBUG
1397         bool "Lots of debug output from Radeon driver"
1398         depends on FB_RADEON
1399         default n
1400         help
1401           Say Y here if you want the Radeon driver to output all sorts
1402           of debugging information to provide to the maintainer when
1403           something goes wrong.
1404 
1405 config FB_ATY128
1406         tristate "ATI Rage128 display support"
1407         depends on FB && PCI
1408         select FB_CFB_FILLRECT
1409         select FB_CFB_COPYAREA
1410         select FB_CFB_IMAGEBLIT
1411         select FB_BACKLIGHT if FB_ATY128_BACKLIGHT
1412         select FB_MACMODES if PPC_PMAC
1413         help
1414           This driver supports graphics boards with the ATI Rage128 chips.
1415           Say Y if you have such a graphics board and read
1416           <file:Documentation/fb/aty128fb.txt>.
1417 
1418           To compile this driver as a module, choose M here: the
1419           module will be called aty128fb.
1420 
1421 config FB_ATY128_BACKLIGHT
1422         bool "Support for backlight control"
1423         depends on FB_ATY128
1424         default y
1425         help
1426           Say Y here if you want to control the backlight of your display.
1427 
1428 config FB_ATY
1429         tristate "ATI Mach64 display support" if PCI || ATARI
1430         depends on FB && !SPARC32
1431         select FB_CFB_FILLRECT
1432         select FB_CFB_COPYAREA
1433         select FB_CFB_IMAGEBLIT
1434         select FB_BACKLIGHT if FB_ATY_BACKLIGHT
1435         select FB_MACMODES if PPC
1436         help
1437           This driver supports graphics boards with the ATI Mach64 chips.
1438           Say Y if you have such a graphics board.
1439 
1440           To compile this driver as a module, choose M here: the
1441           module will be called atyfb.
1442 
1443 config FB_ATY_CT
1444         bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support"
1445         depends on PCI && FB_ATY
1446         default y if SPARC64 && PCI
1447         help
1448           Say Y here to support use of ATI's 64-bit Rage boards (or other
1449           boards based on the Mach64 CT, VT, GT, and LT chipsets) as a
1450           framebuffer device.  The ATI product support page for these boards
1451           is at <http://support.ati.com/products/pc/mach64/mach64.html>.
1452 
1453 config FB_ATY_GENERIC_LCD
1454         bool "Mach64 generic LCD support"
1455         depends on FB_ATY_CT
1456         help
1457           Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility,
1458           Rage XC, or Rage XL chipset.
1459 
1460 config FB_ATY_GX
1461         bool "Mach64 GX support" if PCI
1462         depends on FB_ATY
1463         default y if ATARI
1464         help
1465           Say Y here to support use of the ATI Mach64 Graphics Expression
1466           board (or other boards based on the Mach64 GX chipset) as a
1467           framebuffer device.  The ATI product support page for these boards
1468           is at
1469           <http://support.ati.com/products/pc/mach64/graphics_xpression.html>.
1470 
1471 config FB_ATY_BACKLIGHT
1472         bool "Support for backlight control"
1473         depends on FB_ATY
1474         default y
1475         help
1476           Say Y here if you want to control the backlight of your display.
1477 
1478 config FB_S3
1479         tristate "S3 Trio/Virge support"
1480         depends on FB && PCI
1481         select FB_CFB_FILLRECT
1482         select FB_CFB_COPYAREA
1483         select FB_CFB_IMAGEBLIT
1484         select FB_TILEBLITTING
1485         select FB_SVGALIB
1486         select VGASTATE
1487         select FONT_8x16 if FRAMEBUFFER_CONSOLE
1488         ---help---
1489           Driver for graphics boards with S3 Trio / S3 Virge chip.
1490 
1491 config FB_S3_DDC
1492         bool "DDC for S3 support"
1493         depends on FB_S3
1494         select FB_DDC
1495         default y
1496         help
1497           Say Y here if you want DDC support for your S3 graphics card.
1498 
1499 config FB_SAVAGE
1500         tristate "S3 Savage support"
1501         depends on FB && PCI
1502         select FB_MODE_HELPERS
1503         select FB_CFB_FILLRECT
1504         select FB_CFB_COPYAREA
1505         select FB_CFB_IMAGEBLIT
1506         select VGASTATE
1507         help
1508           This driver supports notebooks and computers with S3 Savage PCI/AGP
1509           chips.
1510 
1511           Say Y if you have such a graphics card.
1512 
1513           To compile this driver as a module, choose M here; the module
1514           will be called savagefb.
1515 
1516 config FB_SAVAGE_I2C
1517        bool "Enable DDC2 Support"
1518        depends on FB_SAVAGE
1519        select FB_DDC
1520        help
1521           This enables I2C support for S3 Savage Chipsets.  This is used
1522           only for getting EDID information from the attached display
1523           allowing for robust video mode handling and switching.
1524 
1525           Because fbdev-2.6 requires that drivers must be able to
1526           independently validate video mode parameters, you should say Y
1527           here.
1528 
1529 config FB_SAVAGE_ACCEL
1530        bool "Enable Console Acceleration"
1531        depends on FB_SAVAGE
1532        default n
1533        help
1534           This option will compile in console acceleration support. If
1535           the resulting framebuffer console has bothersome glitches, then
1536           choose N here.
1537 
1538 config FB_SIS
1539         tristate "SiS/XGI display support"
1540         depends on FB && PCI
1541         select FB_CFB_FILLRECT
1542         select FB_CFB_COPYAREA
1543         select FB_CFB_IMAGEBLIT
1544         select FB_BOOT_VESA_SUPPORT if FB_SIS = y
1545         help
1546           This is the frame buffer device driver for the SiS 300, 315, 330
1547           and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets.
1548           Specs available at <http://www.sis.com> and <http://www.xgitech.com>.
1549 
1550           To compile this driver as a module, choose M here; the module
1551           will be called sisfb.
1552 
1553 config FB_SIS_300
1554         bool "SiS 300 series support"
1555         depends on FB_SIS
1556         help
1557           Say Y here to support use of the SiS 300/305, 540, 630 and 730.
1558 
1559 config FB_SIS_315
1560         bool "SiS 315/330/340 series and XGI support"
1561         depends on FB_SIS
1562         help
1563           Say Y here to support use of the SiS 315, 330 and 340 series
1564           (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well
1565           as XGI V3XT, V5, V8 and Z7.
1566 
1567 config FB_VIA
1568        tristate "VIA UniChrome (Pro) and Chrome9 display support"
1569        depends on FB && PCI && X86
1570        select FB_CFB_FILLRECT
1571        select FB_CFB_COPYAREA
1572        select FB_CFB_IMAGEBLIT
1573        select I2C_ALGOBIT
1574        select I2C
1575        select GPIOLIB
1576        help
1577           This is the frame buffer device driver for Graphics chips of VIA
1578           UniChrome (Pro) Family (CLE266,PM800/CN400,P4M800CE/P4M800Pro/
1579           CN700/VN800,CX700/VX700,P4M890) and Chrome9 Family (K8M890,CN896
1580           /P4M900,VX800)
1581           Say Y if you have a VIA UniChrome graphics board.
1582 
1583           To compile this driver as a module, choose M here: the
1584           module will be called viafb.
1585 
1586 if FB_VIA
1587 
1588 config FB_VIA_DIRECT_PROCFS
1589         bool "direct hardware access via procfs (DEPRECATED)(DANGEROUS)"
1590         depends on FB_VIA
1591         default n
1592         help
1593           Allow direct hardware access to some output registers via procfs.
1594           This is dangerous but may provide the only chance to get the
1595           correct output device configuration.
1596           Its use is strongly discouraged.
1597 
1598 config FB_VIA_X_COMPATIBILITY
1599         bool "X server compatibility"
1600         depends on FB_VIA
1601         default n
1602         help
1603           This option reduces the functionality (power saving, ...) of the
1604           framebuffer to avoid negative impact on the OpenChrome X server.
1605           If you use any X server other than fbdev you should enable this
1606           otherwise it should be safe to disable it and allow using all
1607           features.
1608 
1609 endif
1610 
1611 config FB_NEOMAGIC
1612         tristate "NeoMagic display support"
1613         depends on FB && PCI
1614         select FB_MODE_HELPERS
1615         select FB_CFB_FILLRECT
1616         select FB_CFB_COPYAREA
1617         select FB_CFB_IMAGEBLIT
1618         select VGASTATE
1619         help
1620           This driver supports notebooks with NeoMagic PCI chips.
1621           Say Y if you have such a graphics card. 
1622 
1623           To compile this driver as a module, choose M here: the
1624           module will be called neofb.
1625 
1626 config FB_KYRO
1627         tristate "IMG Kyro support"
1628         depends on FB && PCI
1629         select FB_CFB_FILLRECT
1630         select FB_CFB_COPYAREA
1631         select FB_CFB_IMAGEBLIT
1632         help
1633           Say Y here if you have a STG4000 / Kyro / PowerVR 3 based
1634           graphics board.
1635 
1636           To compile this driver as a module, choose M here: the
1637           module will be called kyrofb.
1638 
1639 config FB_3DFX
1640         tristate "3Dfx Banshee/Voodoo3/Voodoo5 display support"
1641         depends on FB && PCI
1642         select FB_CFB_IMAGEBLIT
1643         select FB_CFB_FILLRECT
1644         select FB_CFB_COPYAREA
1645         select FB_MODE_HELPERS
1646         help
1647           This driver supports graphics boards with the 3Dfx Banshee,
1648           Voodoo3 or VSA-100 (aka Voodoo4/5) chips. Say Y if you have
1649           such a graphics board.
1650 
1651           To compile this driver as a module, choose M here: the
1652           module will be called tdfxfb.
1653 
1654 config FB_3DFX_ACCEL
1655         bool "3Dfx Acceleration functions"
1656         depends on FB_3DFX
1657         ---help---
1658         This will compile the 3Dfx Banshee/Voodoo3/VSA-100 frame buffer
1659         device driver with acceleration functions.
1660 
1661 config FB_3DFX_I2C
1662         bool "Enable DDC/I2C support"
1663         depends on FB_3DFX
1664         select FB_DDC
1665         default y
1666         help
1667           Say Y here if you want DDC/I2C support for your 3dfx Voodoo3.
1668 
1669 config FB_VOODOO1
1670         tristate "3Dfx Voodoo Graphics (sst1) support"
1671         depends on FB && PCI
1672         select FB_CFB_FILLRECT
1673         select FB_CFB_COPYAREA
1674         select FB_CFB_IMAGEBLIT
1675         ---help---
1676           Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or 
1677           Voodoo2 (cvg) based graphics card.
1678 
1679           To compile this driver as a module, choose M here: the
1680           module will be called sstfb.
1681 
1682           WARNING: Do not use any application that uses the 3D engine
1683           (namely glide) while using this driver.
1684           Please read the <file:Documentation/fb/sstfb.txt> for supported
1685           options and other important info  support.
1686 
1687 config FB_VT8623
1688         tristate "VIA VT8623 support"
1689         depends on FB && PCI
1690         select FB_CFB_FILLRECT
1691         select FB_CFB_COPYAREA
1692         select FB_CFB_IMAGEBLIT
1693         select FB_TILEBLITTING
1694         select FB_SVGALIB
1695         select VGASTATE
1696         select FONT_8x16 if FRAMEBUFFER_CONSOLE
1697         ---help---
1698           Driver for CastleRock integrated graphics core in the
1699           VIA VT8623 [Apollo CLE266] chipset.
1700 
1701 config FB_TRIDENT
1702         tristate "Trident/CyberXXX/CyberBlade support"
1703         depends on FB && PCI
1704         select FB_CFB_FILLRECT
1705         select FB_CFB_COPYAREA
1706         select FB_CFB_IMAGEBLIT
1707         ---help---
1708           This is the frame buffer device driver for Trident PCI/AGP chipsets.
1709           Supported chipset families are TGUI 9440/96XX, 3DImage, Blade3D
1710           and Blade XP.
1711           There are also integrated versions of these chips called CyberXXXX,
1712           CyberImage or CyberBlade. These chips are mostly found in laptops
1713           but also on some motherboards including early VIA EPIA motherboards.
1714           For more information, read <file:Documentation/fb/tridentfb.txt>
1715 
1716           Say Y if you have such a graphics board.
1717 
1718           To compile this driver as a module, choose M here: the
1719           module will be called tridentfb.
1720 
1721 config FB_ARK
1722         tristate "ARK 2000PV support"
1723         depends on FB && PCI
1724         select FB_CFB_FILLRECT
1725         select FB_CFB_COPYAREA
1726         select FB_CFB_IMAGEBLIT
1727         select FB_TILEBLITTING
1728         select FB_SVGALIB
1729         select VGASTATE
1730         select FONT_8x16 if FRAMEBUFFER_CONSOLE
1731         ---help---
1732           Driver for PCI graphics boards with ARK 2000PV chip
1733           and ICS 5342 RAMDAC.
1734 
1735 config FB_PM3
1736         tristate "Permedia3 support"
1737         depends on FB && PCI
1738         select FB_CFB_FILLRECT
1739         select FB_CFB_COPYAREA
1740         select FB_CFB_IMAGEBLIT
1741         help
1742           This is the frame buffer device driver for the 3DLabs Permedia3
1743           chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 &
1744           similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000
1745           and maybe other boards.
1746 
1747 config FB_CARMINE
1748         tristate "Fujitsu carmine frame buffer support"
1749         depends on FB && PCI
1750         select FB_CFB_FILLRECT
1751         select FB_CFB_COPYAREA
1752         select FB_CFB_IMAGEBLIT
1753         help
1754           This is the frame buffer device driver for the Fujitsu Carmine chip.
1755           The driver provides two independent frame buffer devices.
1756 
1757 choice
1758         depends on FB_CARMINE
1759         prompt "DRAM timing"
1760         default FB_CARMINE_DRAM_EVAL
1761 
1762 config FB_CARMINE_DRAM_EVAL
1763         bool "Eval board timings"
1764         help
1765           Use timings which work on the eval card.
1766 
1767 config CARMINE_DRAM_CUSTOM
1768         bool "Custom board timings"
1769         help
1770           Use custom board timings.
1771 endchoice
1772 
1773 config FB_AU1100
1774         bool "Au1100 LCD Driver"
1775         depends on (FB = y) && MIPS_ALCHEMY
1776         select FB_CFB_FILLRECT
1777         select FB_CFB_COPYAREA
1778         select FB_CFB_IMAGEBLIT
1779         help
1780           This is the framebuffer driver for the AMD Au1100 SOC.  It can drive
1781           various panels and CRTs by passing in kernel cmd line option
1782           au1100fb:panel=<name>.
1783 
1784 config FB_AU1200
1785         bool "Au1200/Au1300 LCD Driver"
1786         depends on (FB = y) && MIPS_ALCHEMY
1787         select FB_SYS_FILLRECT
1788         select FB_SYS_COPYAREA
1789         select FB_SYS_IMAGEBLIT
1790         select FB_SYS_FOPS
1791         help
1792           This is the framebuffer driver for the Au1200/Au1300 SOCs.
1793           It can drive various panels and CRTs by passing in kernel cmd line
1794           option au1200fb:panel=<name>.
1795 
1796 config FB_VT8500
1797         bool "VIA VT8500 framebuffer support"
1798         depends on (FB = y) && ARM && ARCH_VT8500
1799         select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
1800         select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
1801         select FB_SYS_IMAGEBLIT
1802         select FB_MODE_HELPERS
1803         select VIDEOMODE_HELPERS
1804         help
1805           This is the framebuffer driver for VIA VT8500 integrated LCD
1806           controller.
1807 
1808 config FB_WM8505
1809         bool "Wondermedia WM8xxx-series frame buffer support"
1810         depends on (FB = y) && ARM && ARCH_VT8500
1811         select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
1812         select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
1813         select FB_SYS_IMAGEBLIT
1814         select FB_MODE_HELPERS
1815         select VIDEOMODE_HELPERS
1816         help
1817           This is the framebuffer driver for WonderMedia WM8xxx-series
1818           integrated LCD controller. This driver covers the WM8505, WM8650
1819           and WM8850 SoCs.
1820 
1821 config FB_WMT_GE_ROPS
1822         bool "VT8500/WM8xxx accelerated raster ops support"
1823         depends on (FB = y) && (FB_VT8500 || FB_WM8505)
1824         default n
1825         help
1826           This adds support for accelerated raster operations on the
1827           VIA VT8500 and Wondermedia 85xx series SoCs.
1828 
1829 source "drivers/video/geode/Kconfig"
1830 
1831 config FB_HIT
1832         tristate "HD64461 Frame Buffer support"
1833         depends on FB && HD64461
1834         select FB_CFB_FILLRECT
1835         select FB_CFB_COPYAREA
1836         select FB_CFB_IMAGEBLIT
1837         help
1838           This is the frame buffer device driver for the Hitachi HD64461 LCD
1839           frame buffer card.
1840 
1841 config FB_PMAG_AA
1842         bool "PMAG-AA TURBOchannel framebuffer support"
1843         depends on (FB = y) && TC
1844         select FB_CFB_FILLRECT
1845         select FB_CFB_COPYAREA
1846         select FB_CFB_IMAGEBLIT
1847         help
1848           Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1)
1849           used mainly in the MIPS-based DECstation series.
1850 
1851 config FB_PMAG_BA
1852         tristate "PMAG-BA TURBOchannel framebuffer support"
1853         depends on FB && TC
1854         select FB_CFB_FILLRECT
1855         select FB_CFB_COPYAREA
1856         select FB_CFB_IMAGEBLIT
1857         help
1858           Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8)
1859           used mainly in the MIPS-based DECstation series.
1860 
1861 config FB_PMAGB_B
1862         tristate "PMAGB-B TURBOchannel framebuffer support"
1863         depends on FB && TC
1864         select FB_CFB_FILLRECT
1865         select FB_CFB_COPYAREA
1866         select FB_CFB_IMAGEBLIT
1867         help
1868           Support for the PMAGB-B TURBOchannel framebuffer card used mainly
1869           in the MIPS-based DECstation series. The card is currently only
1870           supported in 1280x1024x8 mode.
1871 
1872 config FB_MAXINE
1873         bool "Maxine (Personal DECstation) onboard framebuffer support"
1874         depends on (FB = y) && MACH_DECSTATION
1875         select FB_CFB_FILLRECT
1876         select FB_CFB_COPYAREA
1877         select FB_CFB_IMAGEBLIT
1878         help
1879           Support for the onboard framebuffer (1024x768x8) in the Personal
1880           DECstation series (Personal DECstation 5000/20, /25, /33, /50,
1881           Codename "Maxine").
1882 
1883 config FB_G364
1884         bool "G364 frame buffer support"
1885         depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700)
1886         select FB_CFB_FILLRECT
1887         select FB_CFB_COPYAREA
1888         select FB_CFB_IMAGEBLIT
1889         help
1890           The G364 driver is the framebuffer used in MIPS Magnum 4000 and
1891           Olivetti M700-10 systems.
1892 
1893 config FB_68328
1894         bool "Motorola 68328 native frame buffer support"
1895         depends on (FB = y) && (M68328 || M68EZ328 || M68VZ328)
1896         select FB_CFB_FILLRECT
1897         select FB_CFB_COPYAREA
1898         select FB_CFB_IMAGEBLIT
1899         help
1900           Say Y here if you want to support the built-in frame buffer of
1901           the Motorola 68328 CPU family.
1902 
1903 config FB_PXA168
1904         tristate "PXA168/910 LCD framebuffer support"
1905         depends on FB && (CPU_PXA168 || CPU_PXA910)
1906         select FB_CFB_FILLRECT
1907         select FB_CFB_COPYAREA
1908         select FB_CFB_IMAGEBLIT
1909         ---help---
1910           Frame buffer driver for the built-in LCD controller in the Marvell
1911           MMP processor.
1912 
1913 config FB_PXA
1914         tristate "PXA LCD framebuffer support"
1915         depends on FB && ARCH_PXA
1916         select FB_CFB_FILLRECT
1917         select FB_CFB_COPYAREA
1918         select FB_CFB_IMAGEBLIT
1919         ---help---
1920           Frame buffer driver for the built-in LCD controller in the Intel
1921           PXA2x0 processor.
1922 
1923           This driver is also available as a module ( = code which can be
1924           inserted and removed from the running kernel whenever you want). The
1925           module will be called pxafb. If you want to compile it as a module,
1926           say M here and read <file:Documentation/kbuild/modules.txt>.
1927 
1928           If unsure, say N.
1929 
1930 config FB_PXA_OVERLAY
1931         bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer"
1932         default n
1933         depends on FB_PXA && (PXA27x || PXA3xx)
1934 
1935 config FB_PXA_SMARTPANEL
1936         bool "PXA Smartpanel LCD support"
1937         default n
1938         depends on FB_PXA
1939 
1940 config FB_PXA_PARAMETERS
1941         bool "PXA LCD command line parameters"
1942         default n
1943         depends on FB_PXA
1944         ---help---
1945           Enable the use of kernel command line or module parameters
1946           to configure the physical properties of the LCD panel when
1947           using the PXA LCD driver.
1948 
1949           This option allows you to override the panel parameters
1950           supplied by the platform in order to support multiple
1951           different models of flatpanel. If you will only be using a
1952           single model of flatpanel then you can safely leave this
1953           option disabled.
1954 
1955           <file:Documentation/fb/pxafb.txt> describes the available parameters.
1956 
1957 config PXA3XX_GCU
1958         tristate "PXA3xx 2D graphics accelerator driver"
1959         depends on FB_PXA
1960         help
1961           Kernelspace driver for the 2D graphics controller unit (GCU)
1962           found on PXA3xx processors. There is a counterpart driver in the
1963           DirectFB suite, see http://www.directfb.org/
1964 
1965           If you compile this as a module, it will be called pxa3xx_gcu.
1966 
1967 config FB_MBX
1968         tristate "2700G LCD framebuffer support"
1969         depends on FB && ARCH_PXA
1970         select FB_CFB_FILLRECT
1971         select FB_CFB_COPYAREA
1972         select FB_CFB_IMAGEBLIT
1973         ---help---
1974           Framebuffer driver for the Intel 2700G (Marathon) Graphics
1975           Accelerator
1976 
1977 config FB_MBX_DEBUG
1978        bool "Enable debugging info via debugfs"
1979        depends on FB_MBX && DEBUG_FS
1980        default n
1981        ---help---
1982          Enable this if you want debugging information using the debug
1983          filesystem (debugfs)
1984 
1985          If unsure, say N.
1986 
1987 config FB_FSL_DIU
1988         tristate "Freescale DIU framebuffer support"
1989         depends on FB && FSL_SOC
1990         select FB_MODE_HELPERS
1991         select FB_CFB_FILLRECT
1992         select FB_CFB_COPYAREA
1993         select FB_CFB_IMAGEBLIT
1994         select PPC_LIB_RHEAP
1995         ---help---
1996           Framebuffer driver for the Freescale SoC DIU
1997 
1998 config FB_W100
1999         tristate "W100 frame buffer support"
2000         depends on FB && ARCH_PXA
2001         select FB_CFB_FILLRECT
2002         select FB_CFB_COPYAREA
2003         select FB_CFB_IMAGEBLIT
2004         ---help---
2005           Frame buffer driver for the w100 as found on the Sharp SL-Cxx series.
2006           It can also drive the w3220 chip found on iPAQ hx4700.
2007 
2008           This driver is also available as a module ( = code which can be
2009           inserted and removed from the running kernel whenever you want). The
2010           module will be called w100fb. If you want to compile it as a module,
2011           say M here and read <file:Documentation/kbuild/modules.txt>.
2012 
2013           If unsure, say N.
2014 
2015 config FB_SH_MOBILE_LCDC
2016         tristate "SuperH Mobile LCDC framebuffer support"
2017         depends on FB && (SUPERH || ARCH_SHMOBILE) && HAVE_CLK
2018         select FB_SYS_FILLRECT
2019         select FB_SYS_COPYAREA
2020         select FB_SYS_IMAGEBLIT
2021         select FB_SYS_FOPS
2022         select FB_DEFERRED_IO
2023         select FB_BACKLIGHT
2024         select SH_MIPI_DSI if SH_LCD_MIPI_DSI
2025         ---help---
2026           Frame buffer driver for the on-chip SH-Mobile LCD controller.
2027 
2028 config FB_SH_MOBILE_HDMI
2029         tristate "SuperH Mobile HDMI controller support"
2030         depends on FB_SH_MOBILE_LCDC
2031         select FB_MODE_HELPERS
2032         select SOUND
2033         select SND
2034         select SND_SOC
2035         ---help---
2036           Driver for the on-chip SH-Mobile HDMI controller.
2037 
2038 config FB_TMIO
2039         tristate "Toshiba Mobile IO FrameBuffer support"
2040         depends on FB && MFD_CORE
2041         select FB_CFB_FILLRECT
2042         select FB_CFB_COPYAREA
2043         select FB_CFB_IMAGEBLIT
2044         ---help---
2045           Frame buffer driver for the Toshiba Mobile IO integrated as found
2046           on the Sharp SL-6000 series
2047 
2048           This driver is also available as a module ( = code which can be
2049           inserted and removed from the running kernel whenever you want). The
2050           module will be called tmiofb. If you want to compile it as a module,
2051           say M here and read <file:Documentation/kbuild/modules.txt>.
2052 
2053           If unsure, say N.
2054 
2055 config FB_TMIO_ACCELL
2056         bool "tmiofb acceleration"
2057         depends on FB_TMIO
2058         default y
2059 
2060 config FB_S3C
2061         tristate "Samsung S3C framebuffer support"
2062         depends on FB && (CPU_S3C2416 || ARCH_S3C64XX || ARCH_S5P64X0 || \
2063                 ARCH_S5PC100 || ARCH_S5PV210 || ARCH_EXYNOS)
2064         select FB_CFB_FILLRECT
2065         select FB_CFB_COPYAREA
2066         select FB_CFB_IMAGEBLIT
2067         ---help---
2068           Frame buffer driver for the built-in FB controller in the Samsung
2069           SoC line from the S3C2443 onwards, including the S3C2416, S3C2450,
2070           and the S3C64XX series such as the S3C6400 and S3C6410.
2071 
2072           These chips all have the same basic framebuffer design with the
2073           actual capabilities depending on the chip. For instance the S3C6400
2074           and S3C6410 support 4 hardware windows whereas the S3C24XX series
2075           currently only have two.
2076 
2077           Currently the support is only for the S3C6400 and S3C6410 SoCs.
2078 
2079 config FB_S3C_DEBUG_REGWRITE
2080        bool "Debug register writes"
2081        depends on FB_S3C
2082        ---help---
2083          Show all register writes via pr_debug()
2084 
2085 config FB_S3C2410
2086         tristate "S3C2410 LCD framebuffer support"
2087         depends on FB && ARCH_S3C24XX
2088         select FB_CFB_FILLRECT
2089         select FB_CFB_COPYAREA
2090         select FB_CFB_IMAGEBLIT
2091         ---help---
2092           Frame buffer driver for the built-in LCD controller in the Samsung
2093           S3C2410 processor.
2094 
2095           This driver is also available as a module ( = code which can be
2096           inserted and removed from the running kernel whenever you want). The
2097           module will be called s3c2410fb. If you want to compile it as a module,
2098           say M here and read <file:Documentation/kbuild/modules.txt>.
2099 
2100           If unsure, say N.
2101 config FB_S3C2410_DEBUG
2102         bool "S3C2410 lcd debug messages"
2103         depends on FB_S3C2410
2104         help
2105           Turn on debugging messages. Note that you can set/unset at run time
2106           through sysfs
2107 
2108 config FB_NUC900
2109         bool "NUC900 LCD framebuffer support"
2110         depends on FB && ARCH_W90X900
2111         select FB_CFB_FILLRECT
2112         select FB_CFB_COPYAREA
2113         select FB_CFB_IMAGEBLIT
2114         ---help---
2115           Frame buffer driver for the built-in LCD controller in the Nuvoton
2116           NUC900 processor
2117 
2118 config GPM1040A0_320X240
2119         bool "Giantplus Technology GPM1040A0 320x240 Color TFT LCD"
2120         depends on FB_NUC900
2121 
2122 config FB_SM501
2123         tristate "Silicon Motion SM501 framebuffer support"
2124         depends on FB && MFD_SM501
2125         select FB_CFB_FILLRECT
2126         select FB_CFB_COPYAREA
2127         select FB_CFB_IMAGEBLIT
2128         ---help---
2129           Frame buffer driver for the CRT and LCD controllers in the Silicon
2130           Motion SM501.
2131 
2132           This driver is also available as a module ( = code which can be
2133           inserted and removed from the running kernel whenever you want). The
2134           module will be called sm501fb. If you want to compile it as a module,
2135           say M here and read <file:Documentation/kbuild/modules.txt>.
2136 
2137           If unsure, say N.
2138 
2139 config FB_SMSCUFX
2140         tristate "SMSC UFX6000/7000 USB Framebuffer support"
2141         depends on FB && USB
2142         select FB_MODE_HELPERS
2143         select FB_SYS_FILLRECT
2144         select FB_SYS_COPYAREA
2145         select FB_SYS_IMAGEBLIT
2146         select FB_SYS_FOPS
2147         select FB_DEFERRED_IO
2148         ---help---
2149           This is a kernel framebuffer driver for SMSC UFX USB devices.
2150           Supports fbdev clients like xf86-video-fbdev, kdrive, fbi, and
2151           mplayer -vo fbdev. Supports both UFX6000 (USB 2.0) and UFX7000
2152           (USB 3.0) devices.
2153           To compile as a module, choose M here: the module name is smscufx.
2154 
2155 config FB_UDL
2156         tristate "Displaylink USB Framebuffer support"
2157         depends on FB && USB
2158         select FB_MODE_HELPERS
2159         select FB_SYS_FILLRECT
2160         select FB_SYS_COPYAREA
2161         select FB_SYS_IMAGEBLIT
2162         select FB_SYS_FOPS
2163         select FB_DEFERRED_IO
2164         ---help---
2165           This is a kernel framebuffer driver for DisplayLink USB devices.
2166           Supports fbdev clients like xf86-video-fbdev, kdrive, fbi, and
2167           mplayer -vo fbdev. Supports all USB 2.0 era DisplayLink devices.
2168           To compile as a module, choose M here: the module name is udlfb.
2169 
2170 config FB_IBM_GXT4500
2171         tristate "Framebuffer support for IBM GXT4000P/4500P/6000P/6500P adaptors"
2172         depends on FB && PPC
2173         select FB_CFB_FILLRECT
2174         select FB_CFB_COPYAREA
2175         select FB_CFB_IMAGEBLIT
2176         ---help---
2177           Say Y here to enable support for the IBM GXT4000P/6000P and
2178           GXT4500P/6500P display adaptor based on Raster Engine RC1000,
2179           found on some IBM System P (pSeries) machines. This driver
2180           doesn't use Geometry Engine GT1000.
2181 
2182 config FB_PS3
2183         tristate "PS3 GPU framebuffer driver"
2184         depends on FB && PS3_PS3AV
2185         select FB_SYS_FILLRECT
2186         select FB_SYS_COPYAREA
2187         select FB_SYS_IMAGEBLIT
2188         select FB_SYS_FOPS
2189         select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE
2190         ---help---
2191           Include support for the virtual frame buffer in the PS3 platform.
2192 
2193 config FB_PS3_DEFAULT_SIZE_M
2194         int "PS3 default frame buffer size (in MiB)"
2195         depends on FB_PS3
2196         default 9
2197         ---help---
2198           This is the default size (in MiB) of the virtual frame buffer in
2199           the PS3.
2200           The default value can be overridden on the kernel command line
2201           using the "ps3fb" option (e.g. "ps3fb=9M");
2202 
2203 config FB_XILINX
2204         tristate "Xilinx frame buffer support"
2205         depends on FB && (XILINX_VIRTEX || MICROBLAZE || ARCH_ZYNQ)
2206         select FB_CFB_FILLRECT
2207         select FB_CFB_COPYAREA
2208         select FB_CFB_IMAGEBLIT
2209         ---help---
2210           Include support for the Xilinx ML300/ML403 reference design
2211           framebuffer. ML300 carries a 640*480 LCD display on the board,
2212           ML403 uses a standard DB15 VGA connector.
2213 
2214 config FB_GOLDFISH
2215         tristate "Goldfish Framebuffer"
2216         depends on FB && HAS_DMA
2217         select FB_CFB_FILLRECT
2218         select FB_CFB_COPYAREA
2219         select FB_CFB_IMAGEBLIT
2220         ---help---
2221           Framebuffer driver for Goldfish Virtual Platform
2222 
2223 config FB_COBALT
2224         tristate "Cobalt server LCD frame buffer support"
2225         depends on FB && (MIPS_COBALT || MIPS_SEAD3)
2226 
2227 config FB_SH7760
2228         bool "SH7760/SH7763/SH7720/SH7721 LCDC support"
2229         depends on FB && (CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7763 \
2230                 || CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721)
2231         select FB_CFB_FILLRECT
2232         select FB_CFB_COPYAREA
2233         select FB_CFB_IMAGEBLIT
2234         ---help---
2235           Support for the SH7760/SH7763/SH7720/SH7721 integrated
2236           (D)STN/TFT LCD Controller.
2237           Supports display resolutions up to 1024x1024 pixel, grayscale and
2238           color operation, with depths ranging from 1 bpp to 8 bpp monochrome
2239           and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for
2240           panels <= 320 pixel horizontal resolution.
2241 
2242 config FB_DA8XX
2243         tristate "DA8xx/OMAP-L1xx/AM335x Framebuffer support"
2244         depends on FB && (ARCH_DAVINCI_DA8XX || SOC_AM33XX)
2245         select FB_CFB_FILLRECT
2246         select FB_CFB_COPYAREA
2247         select FB_CFB_IMAGEBLIT
2248         select FB_CFB_REV_PIXELS_IN_BYTE
2249         select FB_MODE_HELPERS
2250         select VIDEOMODE_HELPERS
2251         ---help---
2252           This is the frame buffer device driver for the TI LCD controller
2253           found on DA8xx/OMAP-L1xx/AM335x SoCs.
2254           If unsure, say N.
2255 
2256 config FB_VIRTUAL
2257         tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
2258         depends on FB
2259         select FB_SYS_FILLRECT
2260         select FB_SYS_COPYAREA
2261         select FB_SYS_IMAGEBLIT
2262         select FB_SYS_FOPS
2263         ---help---
2264           This is a `virtual' frame buffer device. It operates on a chunk of
2265           unswappable kernel memory instead of on the memory of a graphics
2266           board. This means you cannot see any output sent to this frame
2267           buffer device, while it does consume precious memory. The main use
2268           of this frame buffer device is testing and debugging the frame
2269           buffer subsystem. Do NOT enable it for normal systems! To protect
2270           the innocent, it has to be enabled explicitly at boot time using the
2271           kernel option `video=vfb:'.
2272 
2273           To compile this driver as a module, choose M here: the
2274           module will be called vfb. In order to load it, you must use
2275           the vfb_enable=1 option.
2276 
2277           If unsure, say N.
2278 
2279 config XEN_FBDEV_FRONTEND
2280         tristate "Xen virtual frame buffer support"
2281         depends on FB && XEN
2282         select FB_SYS_FILLRECT
2283         select FB_SYS_COPYAREA
2284         select FB_SYS_IMAGEBLIT
2285         select FB_SYS_FOPS
2286         select FB_DEFERRED_IO
2287         select INPUT_XEN_KBDDEV_FRONTEND if INPUT_MISC
2288         select XEN_XENBUS_FRONTEND
2289         default y
2290         help
2291           This driver implements the front-end of the Xen virtual
2292           frame buffer driver.  It communicates with a back-end
2293           in another domain.
2294 
2295 config FB_METRONOME
2296         tristate "E-Ink Metronome/8track controller support"
2297         depends on FB
2298         select FB_SYS_FILLRECT
2299         select FB_SYS_COPYAREA
2300         select FB_SYS_IMAGEBLIT
2301         select FB_SYS_FOPS
2302         select FB_DEFERRED_IO
2303         help
2304           This driver implements support for the E-Ink Metronome
2305           controller. The pre-release name for this device was 8track
2306           and could also have been called by some vendors as PVI-nnnn.
2307 
2308 config FB_MB862XX
2309         tristate "Fujitsu MB862xx GDC support"
2310         depends on FB
2311         depends on PCI || (OF && PPC)
2312         select FB_CFB_FILLRECT
2313         select FB_CFB_COPYAREA
2314         select FB_CFB_IMAGEBLIT
2315         ---help---
2316           Frame buffer driver for Fujitsu Carmine/Coral-P(A)/Lime controllers.
2317 
2318 choice
2319         prompt "GDC variant"
2320         depends on FB_MB862XX
2321 
2322 config FB_MB862XX_PCI_GDC
2323         bool "Carmine/Coral-P(A) GDC"
2324         depends on PCI
2325         ---help---
2326           This enables framebuffer support for Fujitsu Carmine/Coral-P(A)
2327           PCI graphics controller devices.
2328 
2329 config FB_MB862XX_LIME
2330         bool "Lime GDC"
2331         depends on OF && PPC
2332         select FB_FOREIGN_ENDIAN
2333         select FB_LITTLE_ENDIAN
2334         ---help---
2335           Framebuffer support for Fujitsu Lime GDC on host CPU bus.
2336 
2337 endchoice
2338 
2339 config FB_MB862XX_I2C
2340         bool "Support I2C bus on MB862XX GDC"
2341         depends on FB_MB862XX && I2C
2342         default y
2343         help
2344           Selecting this option adds Coral-P(A)/Lime GDC I2C bus adapter
2345           driver to support accessing I2C devices on controller's I2C bus.
2346           These are usually some video decoder chips.
2347 
2348 config FB_EP93XX
2349         tristate "EP93XX frame buffer support"
2350         depends on FB && ARCH_EP93XX
2351         select FB_CFB_FILLRECT
2352         select FB_CFB_COPYAREA
2353         select FB_CFB_IMAGEBLIT
2354         ---help---
2355           Framebuffer driver for the Cirrus Logic EP93XX series of processors.
2356           This driver is also available as a module. The module will be called
2357           ep93xx-fb.
2358 
2359 config FB_PRE_INIT_FB
2360         bool "Don't reinitialize, use bootloader's GDC/Display configuration"
2361         depends on FB && FB_MB862XX_LIME
2362         ---help---
2363           Select this option if display contents should be inherited as set by
2364           the bootloader.
2365 
2366 config FB_MSM
2367         tristate "MSM Framebuffer support"
2368         depends on FB && ARCH_MSM
2369         select FB_CFB_FILLRECT
2370         select FB_CFB_COPYAREA
2371         select FB_CFB_IMAGEBLIT
2372 
2373 config FB_MX3
2374         tristate "MX3 Framebuffer support"
2375         depends on FB && MX3_IPU
2376         select FB_CFB_FILLRECT
2377         select FB_CFB_COPYAREA
2378         select FB_CFB_IMAGEBLIT
2379         default y
2380         help
2381           This is a framebuffer device for the i.MX31 LCD Controller. So
2382           far only synchronous displays are supported. If you plan to use
2383           an LCD display with your i.MX31 system, say Y here.
2384 
2385 config FB_BROADSHEET
2386         tristate "E-Ink Broadsheet/Epson S1D13521 controller support"
2387         depends on FB
2388         select FB_SYS_FILLRECT
2389         select FB_SYS_COPYAREA
2390         select FB_SYS_IMAGEBLIT
2391         select FB_SYS_FOPS
2392         select FB_DEFERRED_IO
2393         help
2394           This driver implements support for the E-Ink Broadsheet
2395           controller. The release name for this device was Epson S1D13521
2396           and could also have been called by other names when coupled with
2397           a bridge adapter.
2398 
2399 config FB_AUO_K190X
2400         tristate "AUO-K190X EPD controller support"
2401         depends on FB
2402         select FB_SYS_FILLRECT
2403         select FB_SYS_COPYAREA
2404         select FB_SYS_IMAGEBLIT
2405         select FB_SYS_FOPS
2406         select FB_DEFERRED_IO
2407         help
2408           Provides support for epaper controllers from the K190X series
2409           of AUO. These controllers can be used to drive epaper displays
2410           from Sipix.
2411 
2412           This option enables the common support, shared by the individual
2413           controller drivers. You will also have to enable the driver
2414           for the controller type used in your device.
2415 
2416 config FB_AUO_K1900
2417         tristate "AUO-K1900 EPD controller support"
2418         depends on FB && FB_AUO_K190X
2419         help
2420           This driver implements support for the AUO K1900 epd-controller.
2421           This controller can drive Sipix epaper displays but can only do
2422           serial updates, reducing the number of possible frames per second.
2423 
2424 config FB_AUO_K1901
2425         tristate "AUO-K1901 EPD controller support"
2426         depends on FB && FB_AUO_K190X
2427         help
2428           This driver implements support for the AUO K1901 epd-controller.
2429           This controller can drive Sipix epaper displays and supports
2430           concurrent updates, making higher frames per second possible.
2431 
2432 config FB_JZ4740
2433         tristate "JZ4740 LCD framebuffer support"
2434         depends on FB && MACH_JZ4740
2435         select FB_SYS_FILLRECT
2436         select FB_SYS_COPYAREA
2437         select FB_SYS_IMAGEBLIT
2438         help
2439           Framebuffer support for the JZ4740 SoC.
2440 
2441 config FB_MXS
2442         tristate "MXS LCD framebuffer support"
2443         depends on FB && ARCH_MXS
2444         select FB_CFB_FILLRECT
2445         select FB_CFB_COPYAREA
2446         select FB_CFB_IMAGEBLIT
2447         select FB_MODE_HELPERS
2448         select VIDEOMODE_HELPERS
2449         help
2450           Framebuffer support for the MXS SoC.
2451 
2452 config FB_PUV3_UNIGFX
2453         tristate "PKUnity v3 Unigfx framebuffer support"
2454         depends on FB && UNICORE32 && ARCH_PUV3
2455         select FB_SYS_FILLRECT
2456         select FB_SYS_COPYAREA
2457         select FB_SYS_IMAGEBLIT
2458         select FB_SYS_FOPS
2459         help
2460           Choose this option if you want to use the Unigfx device as a
2461           framebuffer device. Without the support of PCI & AGP.
2462 
2463 config FB_HYPERV
2464         tristate "Microsoft Hyper-V Synthetic Video support"
2465         depends on FB && HYPERV
2466         select FB_CFB_FILLRECT
2467         select FB_CFB_COPYAREA
2468         select FB_CFB_IMAGEBLIT
2469         help
2470           This framebuffer driver supports Microsoft Hyper-V Synthetic Video.
2471 
2472 config FB_SIMPLE
2473         bool "Simple framebuffer support"
2474         depends on (FB = y)
2475         select FB_CFB_FILLRECT
2476         select FB_CFB_COPYAREA
2477         select FB_CFB_IMAGEBLIT
2478         help
2479           Say Y if you want support for a simple frame-buffer.
2480 
2481           This driver assumes that the display hardware has been initialized
2482           before the kernel boots, and the kernel will simply render to the
2483           pre-allocated frame buffer surface.
2484 
2485           Configuration re: surface address, size, and format must be provided
2486           through device tree, or plain old platform data.
2487 
2488 source "drivers/video/omap/Kconfig"
2489 source "drivers/video/omap2/Kconfig"
2490 source "drivers/video/exynos/Kconfig"
2491 source "drivers/video/mmp/Kconfig"
2492 source "drivers/video/backlight/Kconfig"
2493 
2494 if VT
2495         source "drivers/video/console/Kconfig"
2496 endif
2497 
2498 if FB || SGI_NEWPORT_CONSOLE
2499         source "drivers/video/logo/Kconfig"
2500 endif
2501 
2502 config FB_SH_MOBILE_MERAM
2503         tristate "SuperH Mobile MERAM read ahead support"
2504         depends on (SUPERH || ARCH_SHMOBILE)
2505         select GENERIC_ALLOCATOR
2506         ---help---
2507           Enable MERAM support for the SuperH controller.
2508 
2509           This will allow for caching of the framebuffer to provide more
2510           reliable access under heavy main memory bus traffic situations.
2511           Up to 4 memory channels can be configured, allowing 4 RGB or
2512           2 YCbCr framebuffers to be configured.
2513 
2514 config FB_SSD1307
2515         tristate "Solomon SSD1307 framebuffer support"
2516         depends on FB && I2C
2517         depends on OF
2518         depends on GPIOLIB
2519         select FB_SYS_FOPS
2520         select FB_SYS_FILLRECT
2521         select FB_SYS_COPYAREA
2522         select FB_SYS_IMAGEBLIT
2523         select FB_DEFERRED_IO
2524         select PWM
2525         help
2526           This driver implements support for the Solomon SSD1307
2527           OLED controller over I2C.
2528 
2529 endmenu

This page was automatically generated by LXR 0.3.1 (source).  •  Linux is a registered trademark of Linus Torvalds  •  Contact us