Version:  2.0.40 2.2.26 2.4.37 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7

Linux/drivers/tty/serial/8250/serial_cs.c

  1 /*======================================================================
  2 
  3     A driver for PCMCIA serial devices
  4 
  5     serial_cs.c 1.134 2002/05/04 05:48:53
  6 
  7     The contents of this file are subject to the Mozilla Public
  8     License Version 1.1 (the "License"); you may not use this file
  9     except in compliance with the License. You may obtain a copy of
 10     the License at http://www.mozilla.org/MPL/
 11 
 12     Software distributed under the License is distributed on an "AS
 13     IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
 14     implied. See the License for the specific language governing
 15     rights and limitations under the License.
 16 
 17     The initial developer of the original code is David A. Hinds
 18     <dahinds@users.sourceforge.net>.  Portions created by David A. Hinds
 19     are Copyright (C) 1999 David A. Hinds.  All Rights Reserved.
 20 
 21     Alternatively, the contents of this file may be used under the
 22     terms of the GNU General Public License version 2 (the "GPL"), in which
 23     case the provisions of the GPL are applicable instead of the
 24     above.  If you wish to allow the use of your version of this file
 25     only under the terms of the GPL and not to allow others to use
 26     your version of this file under the MPL, indicate your decision
 27     by deleting the provisions above and replace them with the notice
 28     and other provisions required by the GPL.  If you do not delete
 29     the provisions above, a recipient may use your version of this
 30     file under either the MPL or the GPL.
 31 
 32 ======================================================================*/
 33 
 34 #include <linux/module.h>
 35 #include <linux/moduleparam.h>
 36 #include <linux/kernel.h>
 37 #include <linux/ptrace.h>
 38 #include <linux/slab.h>
 39 #include <linux/string.h>
 40 #include <linux/timer.h>
 41 #include <linux/serial_core.h>
 42 #include <linux/delay.h>
 43 #include <linux/major.h>
 44 #include <asm/io.h>
 45 
 46 #include <pcmcia/cistpl.h>
 47 #include <pcmcia/ciscode.h>
 48 #include <pcmcia/ds.h>
 49 #include <pcmcia/cisreg.h>
 50 
 51 #include "8250.h"
 52 
 53 
 54 /*====================================================================*/
 55 
 56 /* Parameters that can be set with 'insmod' */
 57 
 58 /* Enable the speaker? */
 59 static int do_sound = 1;
 60 /* Skip strict UART tests? */
 61 static int buggy_uart;
 62 
 63 module_param(do_sound, int, 0444);
 64 module_param(buggy_uart, int, 0444);
 65 
 66 /*====================================================================*/
 67 
 68 /* Table of multi-port card ID's */
 69 
 70 struct serial_quirk {
 71         unsigned int manfid;
 72         unsigned int prodid;
 73         int multi;              /* 1 = multifunction, > 1 = # ports */
 74         void (*config)(struct pcmcia_device *);
 75         void (*setup)(struct pcmcia_device *, struct uart_8250_port *);
 76         void (*wakeup)(struct pcmcia_device *);
 77         int (*post)(struct pcmcia_device *);
 78 };
 79 
 80 struct serial_info {
 81         struct pcmcia_device    *p_dev;
 82         int                     ndev;
 83         int                     multi;
 84         int                     slave;
 85         int                     manfid;
 86         int                     prodid;
 87         int                     c950ctrl;
 88         int                     line[4];
 89         const struct serial_quirk *quirk;
 90 };
 91 
 92 struct serial_cfg_mem {
 93         tuple_t tuple;
 94         cisparse_t parse;
 95         u_char buf[256];
 96 };
 97 
 98 /*
 99  * vers_1 5.0, "Brain Boxes", "2-Port RS232 card", "r6"
100  * manfid 0x0160, 0x0104
101  * This card appears to have a 14.7456MHz clock.
102  */
103 /* Generic Modem: MD55x (GPRS/EDGE) have
104  * Elan VPU16551 UART with 14.7456MHz oscillator
105  * manfid 0x015D, 0x4C45
106  */
107 static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_8250_port *uart)
108 {
109         uart->port.uartclk = 14745600;
110 }
111 
112 static int quirk_post_ibm(struct pcmcia_device *link)
113 {
114         u8 val;
115         int ret;
116 
117         ret = pcmcia_read_config_byte(link, 0x800, &val);
118         if (ret)
119                 goto failed;
120 
121         ret = pcmcia_write_config_byte(link, 0x800, val | 1);
122         if (ret)
123                 goto failed;
124         return 0;
125 
126  failed:
127         return -ENODEV;
128 }
129 
130 /*
131  * Nokia cards are not really multiport cards.  Shouldn't this
132  * be handled by setting the quirk entry .multi = 0 | 1 ?
133  */
134 static void quirk_config_nokia(struct pcmcia_device *link)
135 {
136         struct serial_info *info = link->priv;
137 
138         if (info->multi > 1)
139                 info->multi = 1;
140 }
141 
142 static void quirk_wakeup_oxsemi(struct pcmcia_device *link)
143 {
144         struct serial_info *info = link->priv;
145 
146         if (info->c950ctrl)
147                 outb(12, info->c950ctrl + 1);
148 }
149 
150 /* request_region? oxsemi branch does no request_region too... */
151 /*
152  * This sequence is needed to properly initialize MC45 attached to OXCF950.
153  * I tried decreasing these msleep()s, but it worked properly (survived
154  * 1000 stop/start operations) with these timeouts (or bigger).
155  */
156 static void quirk_wakeup_possio_gcc(struct pcmcia_device *link)
157 {
158         struct serial_info *info = link->priv;
159         unsigned int ctrl = info->c950ctrl;
160 
161         outb(0xA, ctrl + 1);
162         msleep(100);
163         outb(0xE, ctrl + 1);
164         msleep(300);
165         outb(0xC, ctrl + 1);
166         msleep(100);
167         outb(0xE, ctrl + 1);
168         msleep(200);
169         outb(0xF, ctrl + 1);
170         msleep(100);
171         outb(0xE, ctrl + 1);
172         msleep(100);
173         outb(0xC, ctrl + 1);
174 }
175 
176 /*
177  * Socket Dual IO: this enables irq's for second port
178  */
179 static void quirk_config_socket(struct pcmcia_device *link)
180 {
181         struct serial_info *info = link->priv;
182 
183         if (info->multi)
184                 link->config_flags |= CONF_ENABLE_ESR;
185 }
186 
187 static const struct serial_quirk quirks[] = {
188         {
189                 .manfid = 0x0160,
190                 .prodid = 0x0104,
191                 .multi  = -1,
192                 .setup  = quirk_setup_brainboxes_0104,
193         }, {
194                 .manfid = 0x015D,
195                 .prodid = 0x4C45,
196                 .multi  = -1,
197                 .setup  = quirk_setup_brainboxes_0104,
198         }, {
199                 .manfid = MANFID_IBM,
200                 .prodid = ~0,
201                 .multi  = -1,
202                 .post   = quirk_post_ibm,
203         }, {
204                 .manfid = MANFID_INTEL,
205                 .prodid = PRODID_INTEL_DUAL_RS232,
206                 .multi  = 2,
207         }, {
208                 .manfid = MANFID_NATINST,
209                 .prodid = PRODID_NATINST_QUAD_RS232,
210                 .multi  = 4,
211         }, {
212                 .manfid = MANFID_NOKIA,
213                 .prodid = ~0,
214                 .multi  = -1,
215                 .config = quirk_config_nokia,
216         }, {
217                 .manfid = MANFID_OMEGA,
218                 .prodid = PRODID_OMEGA_QSP_100,
219                 .multi  = 4,
220         }, {
221                 .manfid = MANFID_OXSEMI,
222                 .prodid = ~0,
223                 .multi  = -1,
224                 .wakeup = quirk_wakeup_oxsemi,
225         }, {
226                 .manfid = MANFID_POSSIO,
227                 .prodid = PRODID_POSSIO_GCC,
228                 .multi  = -1,
229                 .wakeup = quirk_wakeup_possio_gcc,
230         }, {
231                 .manfid = MANFID_QUATECH,
232                 .prodid = PRODID_QUATECH_DUAL_RS232,
233                 .multi  = 2,
234         }, {
235                 .manfid = MANFID_QUATECH,
236                 .prodid = PRODID_QUATECH_DUAL_RS232_D1,
237                 .multi  = 2,
238         }, {
239                 .manfid = MANFID_QUATECH,
240                 .prodid = PRODID_QUATECH_DUAL_RS232_G,
241                 .multi  = 2,
242         }, {
243                 .manfid = MANFID_QUATECH,
244                 .prodid = PRODID_QUATECH_QUAD_RS232,
245                 .multi  = 4,
246         }, {
247                 .manfid = MANFID_SOCKET,
248                 .prodid = PRODID_SOCKET_DUAL_RS232,
249                 .multi  = 2,
250                 .config = quirk_config_socket,
251         }, {
252                 .manfid = MANFID_SOCKET,
253                 .prodid = ~0,
254                 .multi  = -1,
255                 .config = quirk_config_socket,
256         }
257 };
258 
259 
260 static int serial_config(struct pcmcia_device *link);
261 
262 
263 static void serial_remove(struct pcmcia_device *link)
264 {
265         struct serial_info *info = link->priv;
266         int i;
267 
268         dev_dbg(&link->dev, "serial_release\n");
269 
270         /*
271          * Recheck to see if the device is still configured.
272          */
273         for (i = 0; i < info->ndev; i++)
274                 serial8250_unregister_port(info->line[i]);
275 
276         if (!info->slave)
277                 pcmcia_disable_device(link);
278 }
279 
280 static int serial_suspend(struct pcmcia_device *link)
281 {
282         struct serial_info *info = link->priv;
283         int i;
284 
285         for (i = 0; i < info->ndev; i++)
286                 serial8250_suspend_port(info->line[i]);
287 
288         return 0;
289 }
290 
291 static int serial_resume(struct pcmcia_device *link)
292 {
293         struct serial_info *info = link->priv;
294         int i;
295 
296         for (i = 0; i < info->ndev; i++)
297                 serial8250_resume_port(info->line[i]);
298 
299         if (info->quirk && info->quirk->wakeup)
300                 info->quirk->wakeup(link);
301 
302         return 0;
303 }
304 
305 static int serial_probe(struct pcmcia_device *link)
306 {
307         struct serial_info *info;
308 
309         dev_dbg(&link->dev, "serial_attach()\n");
310 
311         /* Create new serial device */
312         info = kzalloc(sizeof(*info), GFP_KERNEL);
313         if (!info)
314                 return -ENOMEM;
315         info->p_dev = link;
316         link->priv = info;
317 
318         link->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IO;
319         if (do_sound)
320                 link->config_flags |= CONF_ENABLE_SPKR;
321 
322         return serial_config(link);
323 }
324 
325 static void serial_detach(struct pcmcia_device *link)
326 {
327         struct serial_info *info = link->priv;
328 
329         dev_dbg(&link->dev, "serial_detach\n");
330 
331         /*
332          * Ensure that the ports have been released.
333          */
334         serial_remove(link);
335 
336         /* free bits */
337         kfree(info);
338 }
339 
340 /*====================================================================*/
341 
342 static int setup_serial(struct pcmcia_device *handle, struct serial_info *info,
343                         unsigned int iobase, int irq)
344 {
345         struct uart_8250_port uart;
346         int line;
347 
348         memset(&uart, 0, sizeof(uart));
349         uart.port.iobase = iobase;
350         uart.port.irq = irq;
351         uart.port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ;
352         uart.port.uartclk = 1843200;
353         uart.port.dev = &handle->dev;
354         if (buggy_uart)
355                 uart.port.flags |= UPF_BUGGY_UART;
356 
357         if (info->quirk && info->quirk->setup)
358                 info->quirk->setup(handle, &uart);
359 
360         line = serial8250_register_8250_port(&uart);
361         if (line < 0) {
362                 pr_err("serial_cs: serial8250_register_8250_port() at 0x%04lx, irq %d failed\n",
363                                                         (unsigned long)iobase, irq);
364                 return -EINVAL;
365         }
366 
367         info->line[info->ndev] = line;
368         info->ndev++;
369 
370         return 0;
371 }
372 
373 /*====================================================================*/
374 
375 static int pfc_config(struct pcmcia_device *p_dev)
376 {
377         unsigned int port = 0;
378         struct serial_info *info = p_dev->priv;
379 
380         if ((p_dev->resource[1]->end != 0) &&
381                 (resource_size(p_dev->resource[1]) == 8)) {
382                 port = p_dev->resource[1]->start;
383                 info->slave = 1;
384         } else if ((info->manfid == MANFID_OSITECH) &&
385                 (resource_size(p_dev->resource[0]) == 0x40)) {
386                 port = p_dev->resource[0]->start + 0x28;
387                 info->slave = 1;
388         }
389         if (info->slave)
390                 return setup_serial(p_dev, info, port, p_dev->irq);
391 
392         dev_warn(&p_dev->dev, "no usable port range found, giving up\n");
393         return -ENODEV;
394 }
395 
396 static int simple_config_check(struct pcmcia_device *p_dev, void *priv_data)
397 {
398         static const int size_table[2] = { 8, 16 };
399         int *try = priv_data;
400 
401         if (p_dev->resource[0]->start == 0)
402                 return -ENODEV;
403 
404         if ((*try & 0x1) == 0)
405                 p_dev->io_lines = 16;
406 
407         if (p_dev->resource[0]->end != size_table[(*try >> 1)])
408                 return -ENODEV;
409 
410         p_dev->resource[0]->end = 8;
411         p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
412         p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
413 
414         return pcmcia_request_io(p_dev);
415 }
416 
417 static int simple_config_check_notpicky(struct pcmcia_device *p_dev,
418                                         void *priv_data)
419 {
420         static const unsigned int base[5] = { 0x3f8, 0x2f8, 0x3e8, 0x2e8, 0x0 };
421         int j;
422 
423         if (p_dev->io_lines > 3)
424                 return -ENODEV;
425 
426         p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
427         p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
428         p_dev->resource[0]->end = 8;
429 
430         for (j = 0; j < 5; j++) {
431                 p_dev->resource[0]->start = base[j];
432                 p_dev->io_lines = base[j] ? 16 : 3;
433                 if (!pcmcia_request_io(p_dev))
434                         return 0;
435         }
436         return -ENODEV;
437 }
438 
439 static int simple_config(struct pcmcia_device *link)
440 {
441         struct serial_info *info = link->priv;
442         int i = -ENODEV, try;
443 
444         /*
445          * First pass: look for a config entry that looks normal.
446          * Two tries: without IO aliases, then with aliases.
447          */
448         link->config_flags |= CONF_AUTO_SET_VPP;
449         for (try = 0; try < 4; try++)
450                 if (!pcmcia_loop_config(link, simple_config_check, &try))
451                         goto found_port;
452 
453         /*
454          * Second pass: try to find an entry that isn't picky about
455          * its base address, then try to grab any standard serial port
456          * address, and finally try to get any free port.
457          */
458         if (!pcmcia_loop_config(link, simple_config_check_notpicky, NULL))
459                 goto found_port;
460 
461         dev_warn(&link->dev, "no usable port range found, giving up\n");
462         return -1;
463 
464 found_port:
465         if (info->multi && (info->manfid == MANFID_3COM))
466                 link->config_index &= ~(0x08);
467 
468         /*
469          * Apply any configuration quirks.
470          */
471         if (info->quirk && info->quirk->config)
472                 info->quirk->config(link);
473 
474         i = pcmcia_enable_device(link);
475         if (i != 0)
476                 return -1;
477         return setup_serial(link, info, link->resource[0]->start, link->irq);
478 }
479 
480 static int multi_config_check(struct pcmcia_device *p_dev, void *priv_data)
481 {
482         int *multi = priv_data;
483 
484         if (p_dev->resource[1]->end)
485                 return -EINVAL;
486 
487         /*
488          * The quad port cards have bad CIS's, so just look for a
489          * window larger than 8 ports and assume it will be right.
490          */
491         if (p_dev->resource[0]->end <= 8)
492                 return -EINVAL;
493 
494         p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
495         p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
496         p_dev->resource[0]->end = *multi * 8;
497 
498         if (pcmcia_request_io(p_dev))
499                 return -ENODEV;
500         return 0;
501 }
502 
503 static int multi_config_check_notpicky(struct pcmcia_device *p_dev,
504                                        void *priv_data)
505 {
506         int *base2 = priv_data;
507 
508         if (!p_dev->resource[0]->end || !p_dev->resource[1]->end ||
509                 p_dev->resource[0]->start + 8 != p_dev->resource[1]->start)
510                 return -ENODEV;
511 
512         p_dev->resource[0]->end = p_dev->resource[1]->end = 8;
513         p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
514         p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
515 
516         if (pcmcia_request_io(p_dev))
517                 return -ENODEV;
518 
519         *base2 = p_dev->resource[0]->start + 8;
520         return 0;
521 }
522 
523 static int multi_config(struct pcmcia_device *link)
524 {
525         struct serial_info *info = link->priv;
526         int i, base2 = 0;
527 
528         /* First, look for a generic full-sized window */
529         if (!pcmcia_loop_config(link, multi_config_check, &info->multi))
530                 base2 = link->resource[0]->start + 8;
531         else {
532                 /* If that didn't work, look for two windows */
533                 info->multi = 2;
534                 if (pcmcia_loop_config(link, multi_config_check_notpicky,
535                                        &base2)) {
536                         dev_warn(&link->dev,
537                                  "no usable port range found, giving up\n");
538                         return -ENODEV;
539                 }
540         }
541 
542         if (!link->irq)
543                 dev_warn(&link->dev, "no usable IRQ found, continuing...\n");
544 
545         /*
546          * Apply any configuration quirks.
547          */
548         if (info->quirk && info->quirk->config)
549                 info->quirk->config(link);
550 
551         i = pcmcia_enable_device(link);
552         if (i != 0)
553                 return -ENODEV;
554 
555         /* The Oxford Semiconductor OXCF950 cards are in fact single-port:
556          * 8 registers are for the UART, the others are extra registers.
557          * Siemen's MC45 PCMCIA (Possio's GCC) is OXCF950 based too.
558          */
559         if (info->manfid == MANFID_OXSEMI || (info->manfid == MANFID_POSSIO &&
560                                 info->prodid == PRODID_POSSIO_GCC)) {
561                 int err;
562 
563                 if (link->config_index == 1 ||
564                     link->config_index == 3) {
565                         err = setup_serial(link, info, base2,
566                                         link->irq);
567                         base2 = link->resource[0]->start;
568                 } else {
569                         err = setup_serial(link, info, link->resource[0]->start,
570                                         link->irq);
571                 }
572                 info->c950ctrl = base2;
573 
574                 /*
575                  * FIXME: We really should wake up the port prior to
576                  * handing it over to the serial layer.
577                  */
578                 if (info->quirk && info->quirk->wakeup)
579                         info->quirk->wakeup(link);
580 
581                 return 0;
582         }
583 
584         setup_serial(link, info, link->resource[0]->start, link->irq);
585         for (i = 0; i < info->multi - 1; i++)
586                 setup_serial(link, info, base2 + (8 * i),
587                                 link->irq);
588         return 0;
589 }
590 
591 static int serial_check_for_multi(struct pcmcia_device *p_dev,  void *priv_data)
592 {
593         struct serial_info *info = p_dev->priv;
594 
595         if (!p_dev->resource[0]->end)
596                 return -EINVAL;
597 
598         if ((!p_dev->resource[1]->end) && (p_dev->resource[0]->end % 8 == 0))
599                 info->multi = p_dev->resource[0]->end >> 3;
600 
601         if ((p_dev->resource[1]->end) && (p_dev->resource[0]->end == 8)
602                 && (p_dev->resource[1]->end == 8))
603                 info->multi = 2;
604 
605         return 0; /* break */
606 }
607 
608 
609 static int serial_config(struct pcmcia_device *link)
610 {
611         struct serial_info *info = link->priv;
612         int i;
613 
614         dev_dbg(&link->dev, "serial_config\n");
615 
616         /* Is this a compliant multifunction card? */
617         info->multi = (link->socket->functions > 1);
618 
619         /* Is this a multiport card? */
620         info->manfid = link->manf_id;
621         info->prodid = link->card_id;
622 
623         for (i = 0; i < ARRAY_SIZE(quirks); i++)
624                 if ((quirks[i].manfid == ~0 ||
625                      quirks[i].manfid == info->manfid) &&
626                     (quirks[i].prodid == ~0 ||
627                      quirks[i].prodid == info->prodid)) {
628                         info->quirk = &quirks[i];
629                         break;
630                 }
631 
632         /*
633          * Another check for dual-serial cards: look for either serial or
634          * multifunction cards that ask for appropriate IO port ranges.
635          */
636         if ((info->multi == 0) &&
637             (link->has_func_id) &&
638             (link->socket->pcmcia_pfc == 0) &&
639             ((link->func_id == CISTPL_FUNCID_MULTI) ||
640              (link->func_id == CISTPL_FUNCID_SERIAL)))
641                 pcmcia_loop_config(link, serial_check_for_multi, info);
642 
643         /*
644          * Apply any multi-port quirk.
645          */
646         if (info->quirk && info->quirk->multi != -1)
647                 info->multi = info->quirk->multi;
648 
649         dev_info(&link->dev,
650                 "trying to set up [0x%04x:0x%04x] (pfc: %d, multi: %d, quirk: %p)\n",
651                 link->manf_id, link->card_id,
652                 link->socket->pcmcia_pfc, info->multi, info->quirk);
653         if (link->socket->pcmcia_pfc)
654                 i = pfc_config(link);
655         else if (info->multi > 1)
656                 i = multi_config(link);
657         else
658                 i = simple_config(link);
659 
660         if (i || info->ndev == 0)
661                 goto failed;
662 
663         /*
664          * Apply any post-init quirk.  FIXME: This should really happen
665          * before we register the port, since it might already be in use.
666          */
667         if (info->quirk && info->quirk->post)
668                 if (info->quirk->post(link))
669                         goto failed;
670 
671         return 0;
672 
673 failed:
674         dev_warn(&link->dev, "failed to initialize\n");
675         serial_remove(link);
676         return -ENODEV;
677 }
678 
679 static const struct pcmcia_device_id serial_ids[] = {
680         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0057, 0x0021),
681         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0089, 0x110a),
682         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0104, 0x000a),
683         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0x0d0a),
684         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0x0e0a),
685         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0xea15),
686         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0109, 0x0501),
687         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0138, 0x110a),
688         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0140, 0x000a),
689         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0143, 0x3341),
690         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0143, 0xc0ab),
691         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x016c, 0x0081),
692         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x021b, 0x0101),
693         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x08a1, 0xc0ab),
694         PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "CC/XJEM3288", "DATA/FAX/CELL ETHERNET MODEM", 0xf510db04, 0x04cd2988, 0x46a52d63),
695         PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "CC/XJEM3336", "DATA/FAX/CELL ETHERNET MODEM", 0xf510db04, 0x0143b773, 0x46a52d63),
696         PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "EM1144T", "PCMCIA MODEM", 0xf510db04, 0x856d66c8, 0xbd6c43ef),
697         PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "XJEM1144/CCEM1144", "PCMCIA MODEM", 0xf510db04, 0x52d21e1e, 0xbd6c43ef),
698         PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM28", 0x2e3ee845, 0x0ea978ea),
699         PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM33", 0x2e3ee845, 0x80609023),
700         PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM56", 0x2e3ee845, 0xa650c32a),
701         PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "REM10", 0x2e3ee845, 0x76df1d29),
702         PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "XEM5600", 0x2e3ee845, 0xf1403719),
703         PCMCIA_PFC_DEVICE_PROD_ID12(1, "AnyCom", "Fast Ethernet + 56K COMBO", 0x578ba6e7, 0xb0ac62c4),
704         PCMCIA_PFC_DEVICE_PROD_ID12(1, "ATKK", "LM33-PCM-T", 0xba9eb7e2, 0x077c174e),
705         PCMCIA_PFC_DEVICE_PROD_ID12(1, "D-Link", "DME336T", 0x1a424a1c, 0xb23897ff),
706         PCMCIA_PFC_DEVICE_PROD_ID12(1, "Gateway 2000", "XJEM3336", 0xdd9989be, 0x662c394c),
707         PCMCIA_PFC_DEVICE_PROD_ID12(1, "Grey Cell", "GCS3000", 0x2a151fac, 0x48b932ae),
708         PCMCIA_PFC_DEVICE_PROD_ID12(1, "Linksys", "EtherFast 10&100 + 56K PC Card (PCMLM56)", 0x0733cc81, 0xb3765033),
709         PCMCIA_PFC_DEVICE_PROD_ID12(1, "LINKSYS", "PCMLM336", 0xf7cb0b07, 0x7a821b58),
710         PCMCIA_PFC_DEVICE_PROD_ID12(1, "MEGAHERTZ", "XJEM1144/CCEM1144", 0xf510db04, 0x52d21e1e),
711         PCMCIA_PFC_DEVICE_PROD_ID12(1, "MICRO RESEARCH", "COMBO-L/M-336", 0xb2ced065, 0x3ced0555),
712         PCMCIA_PFC_DEVICE_PROD_ID12(1, "NEC", "PK-UG-J001", 0x18df0ba0, 0x831b1064),
713         PCMCIA_PFC_DEVICE_PROD_ID12(1, "Ositech", "Trumpcard:Jack of Diamonds Modem+Ethernet", 0xc2f80cd, 0x656947b9),
714         PCMCIA_PFC_DEVICE_PROD_ID12(1, "Ositech", "Trumpcard:Jack of Hearts Modem+Ethernet", 0xc2f80cd, 0xdc9ba5ed),
715         PCMCIA_PFC_DEVICE_PROD_ID12(1, "PCMCIAs", "ComboCard", 0xdcfe12d3, 0xcd8906cc),
716         PCMCIA_PFC_DEVICE_PROD_ID12(1, "PCMCIAs", "LanModem", 0xdcfe12d3, 0xc67c648f),
717         PCMCIA_PFC_DEVICE_PROD_ID12(1, "TDK", "GlobalNetworker 3410/3412", 0x1eae9475, 0xd9a93bed),
718         PCMCIA_PFC_DEVICE_PROD_ID12(1, "Xircom", "CreditCard Ethernet+Modem II", 0x2e3ee845, 0xeca401bf),
719         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0e01),
720         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0a05),
721         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0b05),
722         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x1101),
723         PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0104, 0x0070),
724         PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0101, 0x0562),
725         PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0104, 0x0070),
726         PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x016c, 0x0020),
727         PCMCIA_MFC_DEVICE_PROD_ID123(1, "APEX DATA", "MULTICARD", "ETHERNET-MODEM", 0x11c2da09, 0x7289dc5d, 0xaad95e1f),
728         PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "Home and Away 28.8 PC Card       ", 0xb569a6e5, 0x5bd4ff2c),
729         PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "Home and Away Credit Card Adapter", 0xb569a6e5, 0x4bdf15c3),
730         PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "w95 Home and Away Credit Card ", 0xb569a6e5, 0xae911c15),
731         PCMCIA_MFC_DEVICE_PROD_ID1(1, "Motorola MARQUIS", 0xf03e4e77),
732         PCMCIA_MFC_DEVICE_PROD_ID2(1, "FAX/Modem/Ethernet Combo Card ", 0x1ed59302),
733         PCMCIA_DEVICE_MANF_CARD(0x0089, 0x0301),
734         PCMCIA_DEVICE_MANF_CARD(0x00a4, 0x0276),
735         PCMCIA_DEVICE_MANF_CARD(0x0101, 0x0039),
736         PCMCIA_DEVICE_MANF_CARD(0x0104, 0x0006),
737         PCMCIA_DEVICE_MANF_CARD(0x0105, 0x0101), /* TDK DF2814 */
738         PCMCIA_DEVICE_MANF_CARD(0x0105, 0x100a), /* Xircom CM-56G */
739         PCMCIA_DEVICE_MANF_CARD(0x0105, 0x3e0a), /* TDK DF5660 */
740         PCMCIA_DEVICE_MANF_CARD(0x0105, 0x410a),
741         PCMCIA_DEVICE_MANF_CARD(0x0107, 0x0002), /* USRobotics 14,400 */
742         PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d50),
743         PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d51),
744         PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d52),
745         PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d53),
746         PCMCIA_DEVICE_MANF_CARD(0x010b, 0xd180),
747         PCMCIA_DEVICE_MANF_CARD(0x0115, 0x3330), /* USRobotics/SUN 14,400 */
748         PCMCIA_DEVICE_MANF_CARD(0x0124, 0x0100), /* Nokia DTP-2 ver II */
749         PCMCIA_DEVICE_MANF_CARD(0x0134, 0x5600), /* LASAT COMMUNICATIONS A/S */
750         PCMCIA_DEVICE_MANF_CARD(0x0137, 0x000e),
751         PCMCIA_DEVICE_MANF_CARD(0x0137, 0x001b),
752         PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0025),
753         PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0045),
754         PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0052),
755         PCMCIA_DEVICE_MANF_CARD(0x016c, 0x0006), /* Psion 56K+Fax */
756         PCMCIA_DEVICE_MANF_CARD(0x0200, 0x0001), /* MultiMobile */
757         PCMCIA_DEVICE_PROD_ID134("ADV", "TECH", "COMpad-32/85", 0x67459937, 0x916d02ba, 0x8fbe92ae),
758         PCMCIA_DEVICE_PROD_ID124("GATEWAY2000", "CC3144", "PCMCIA MODEM", 0x506bccae, 0xcb3685f1, 0xbd6c43ef),
759         PCMCIA_DEVICE_PROD_ID14("MEGAHERTZ", "PCMCIA MODEM", 0xf510db04, 0xbd6c43ef),
760         PCMCIA_DEVICE_PROD_ID124("TOSHIBA", "T144PF", "PCMCIA MODEM", 0xb4585a1a, 0x7271409c, 0xbd6c43ef),
761         PCMCIA_DEVICE_PROD_ID123("FUJITSU", "FC14F ", "MBH10213", 0x6ee5a3d8, 0x30ead12b, 0xb00f05a0),
762         PCMCIA_DEVICE_PROD_ID123("Novatel Wireless", "Merlin UMTS Modem", "U630", 0x32607776, 0xd9e73b13, 0xe87332e),
763         PCMCIA_DEVICE_PROD_ID13("MEGAHERTZ", "V.34 PCMCIA MODEM", 0xf510db04, 0xbb2cce4a),
764         PCMCIA_DEVICE_PROD_ID12("Brain Boxes", "Bluetooth PC Card", 0xee138382, 0xd4ce9b02),
765         PCMCIA_DEVICE_PROD_ID12("CIRRUS LOGIC", "FAX MODEM", 0xe625f451, 0xcecd6dfa),
766         PCMCIA_DEVICE_PROD_ID12("COMPAQ", "PCMCIA 28800 FAX/DATA MODEM", 0xa3a3062c, 0x8cbd7c76),
767         PCMCIA_DEVICE_PROD_ID12("COMPAQ", "PCMCIA 33600 FAX/DATA MODEM", 0xa3a3062c, 0x5a00ce95),
768         PCMCIA_DEVICE_PROD_ID12("Computerboards, Inc.", "PCM-COM422", 0xd0b78f51, 0x7e2d49ed),
769         PCMCIA_DEVICE_PROD_ID12("Dr. Neuhaus", "FURY CARD 14K4", 0x76942813, 0x8b96ce65),
770         PCMCIA_DEVICE_PROD_ID12("IBM", "ISDN/56K/GSM", 0xb569a6e5, 0xfee5297b),
771         PCMCIA_DEVICE_PROD_ID12("Intelligent", "ANGIA FAX/MODEM", 0xb496e65e, 0xf31602a6),
772         PCMCIA_DEVICE_PROD_ID12("Intel", "MODEM 2400+", 0x816cc815, 0x412729fb),
773         PCMCIA_DEVICE_PROD_ID12("Intertex", "IX34-PCMCIA", 0xf8a097e3, 0x97880447),
774         PCMCIA_DEVICE_PROD_ID12("IOTech Inc ", "PCMCIA Dual RS-232 Serial Port Card", 0x3bd2d898, 0x92abc92f),
775         PCMCIA_DEVICE_PROD_ID12("MACRONIX", "FAX/MODEM", 0x668388b3, 0x3f9bdf2f),
776         PCMCIA_DEVICE_PROD_ID12("Multi-Tech", "MT1432LT", 0x5f73be51, 0x0b3e2383),
777         PCMCIA_DEVICE_PROD_ID12("Multi-Tech", "MT2834LT", 0x5f73be51, 0x4cd7c09e),
778         PCMCIA_DEVICE_PROD_ID12("OEM      ", "C288MX     ", 0xb572d360, 0xd2385b7a),
779         PCMCIA_DEVICE_PROD_ID12("Option International", "V34bis GSM/PSTN Data/Fax Modem", 0x9d7cd6f5, 0x5cb8bf41),
780         PCMCIA_DEVICE_PROD_ID12("PCMCIA   ", "C336MX     ", 0x99bcafe9, 0xaa25bcab),
781         PCMCIA_DEVICE_PROD_ID12("Quatech Inc", "PCMCIA Dual RS-232 Serial Port Card", 0xc4420b35, 0x92abc92f),
782         PCMCIA_DEVICE_PROD_ID12("Quatech Inc", "Dual RS-232 Serial Port PC Card", 0xc4420b35, 0x031a380d),
783         PCMCIA_DEVICE_PROD_ID12("Telia", "SurfinBird 560P/A+", 0xe2cdd5e, 0xc9314b38),
784         PCMCIA_DEVICE_PROD_ID1("Smart Serial Port", 0x2d8ce292),
785         PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "PCMCIA", "EN2218-LAN/MODEM", 0x281f1c5d, 0x570f348e, "cis/PCMLM28.cis"),
786         PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "PCMCIA", "UE2218-LAN/MODEM", 0x281f1c5d, 0x6fdcacee, "cis/PCMLM28.cis"),
787         PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "Psion Dacom", "Gold Card V34 Ethernet", 0xf5f025c2, 0x338e8155, "cis/PCMLM28.cis"),
788         PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "Psion Dacom", "Gold Card V34 Ethernet GSM", 0xf5f025c2, 0x4ae85d35, "cis/PCMLM28.cis"),
789         PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "LINKSYS", "PCMLM28", 0xf7cb0b07, 0x66881874, "cis/PCMLM28.cis"),
790         PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "TOSHIBA", "Modem/LAN Card", 0xb4585a1a, 0x53f922f8, "cis/PCMLM28.cis"),
791         PCMCIA_MFC_DEVICE_CIS_PROD_ID12(1, "DAYNA COMMUNICATIONS", "LAN AND MODEM MULTIFUNCTION", 0x8fdf8f89, 0xdd5ed9e8, "cis/DP83903.cis"),
792         PCMCIA_MFC_DEVICE_CIS_PROD_ID4(1, "NSC MF LAN/Modem", 0x58fc6056, "cis/DP83903.cis"),
793         PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x0556, "cis/3CCFEM556.cis"),
794         PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0175, 0x0000, "cis/DP83903.cis"),
795         PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x0035, "cis/3CXEM556.cis"),
796         PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x003d, "cis/3CXEM556.cis"),
797         PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC850", 0xd85f6206, 0x42a2c018, "cis/SW_8xx_SER.cis"), /* Sierra Wireless AC850 3G Network Adapter R1 */
798         PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC860", 0xd85f6206, 0x698f93db, "cis/SW_8xx_SER.cis"), /* Sierra Wireless AC860 3G Network Adapter R1 */
799         PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC710/AC750", 0xd85f6206, 0x761b11e0, "cis/SW_7xx_SER.cis"),  /* Sierra Wireless AC710/AC750 GPRS Network Adapter R1 */
800         PCMCIA_DEVICE_CIS_MANF_CARD(0x0192, 0xa555, "cis/SW_555_SER.cis"),  /* Sierra Aircard 555 CDMA 1xrtt Modem -- pre update */
801         PCMCIA_DEVICE_CIS_MANF_CARD(0x013f, 0xa555, "cis/SW_555_SER.cis"),  /* Sierra Aircard 555 CDMA 1xrtt Modem -- post update */
802         PCMCIA_DEVICE_CIS_PROD_ID12("MultiTech", "PCMCIA 56K DataFax", 0x842047ee, 0xc2efcf03, "cis/MT5634ZLX.cis"),
803         PCMCIA_DEVICE_CIS_PROD_ID12("ADVANTECH", "COMpad-32/85B-2", 0x96913a85, 0x27ab5437, "cis/COMpad2.cis"),
804         PCMCIA_DEVICE_CIS_PROD_ID12("ADVANTECH", "COMpad-32/85B-4", 0x96913a85, 0xcec8f102, "cis/COMpad4.cis"),
805         PCMCIA_DEVICE_CIS_PROD_ID123("ADVANTECH", "COMpad-32/85", "1.0", 0x96913a85, 0x8fbe92ae, 0x0877b627, "cis/COMpad2.cis"),
806         PCMCIA_DEVICE_CIS_PROD_ID2("RS-COM 2P", 0xad20b156, "cis/RS-COM-2P.cis"),
807         PCMCIA_DEVICE_CIS_MANF_CARD(0x0013, 0x0000, "cis/GLOBETROTTER.cis"),
808         PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL100  1.00.", 0x19ca78af, 0xf964f42b),
809         PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL100", 0x19ca78af, 0x71d98e83),
810         PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL232  1.00.", 0x19ca78af, 0x69fb7490),
811         PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL232", 0x19ca78af, 0xb6bc0235),
812         PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.", "SERIAL CARD: CF232", 0x63f2e0bd, 0xb9e175d3),
813         PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.", "SERIAL CARD: CF232-5", 0x63f2e0bd, 0xfce33442),
814         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF232", 0x3beb8cf2, 0x171e7190),
815         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF232-5", 0x3beb8cf2, 0x20da4262),
816         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF428", 0x3beb8cf2, 0xea5dd57d),
817         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF500", 0x3beb8cf2, 0xd77255fa),
818         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: IC232", 0x3beb8cf2, 0x6a709903),
819         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: SL232", 0x3beb8cf2, 0x18430676),
820         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: XL232", 0x3beb8cf2, 0x6f933767),
821         PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: CF332", 0x3beb8cf2, 0x16dc1ba7),
822         PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: SL332", 0x3beb8cf2, 0x19816c41),
823         PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: SL385", 0x3beb8cf2, 0x64112029),
824         PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4),
825         PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial+Parallel Port: SP230", 0x3beb8cf2, 0xdb9e58bc),
826         PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: CF332", 0x3beb8cf2, 0x16dc1ba7),
827         PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: SL332", 0x3beb8cf2, 0x19816c41),
828         PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: SL385", 0x3beb8cf2, 0x64112029),
829         PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4),
830         PCMCIA_MFC_DEVICE_PROD_ID12(2, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4),
831         PCMCIA_MFC_DEVICE_PROD_ID12(3, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4),
832         PCMCIA_DEVICE_MANF_CARD(0x0279, 0x950b),
833         /* too generic */
834         /* PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0160, 0x0002), */
835         /* PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0160, 0x0002), */
836         PCMCIA_DEVICE_FUNC_ID(2),
837         PCMCIA_DEVICE_NULL,
838 };
839 MODULE_DEVICE_TABLE(pcmcia, serial_ids);
840 
841 MODULE_FIRMWARE("cis/PCMLM28.cis");
842 MODULE_FIRMWARE("cis/DP83903.cis");
843 MODULE_FIRMWARE("cis/3CCFEM556.cis");
844 MODULE_FIRMWARE("cis/3CXEM556.cis");
845 MODULE_FIRMWARE("cis/SW_8xx_SER.cis");
846 MODULE_FIRMWARE("cis/SW_7xx_SER.cis");
847 MODULE_FIRMWARE("cis/SW_555_SER.cis");
848 MODULE_FIRMWARE("cis/MT5634ZLX.cis");
849 MODULE_FIRMWARE("cis/COMpad2.cis");
850 MODULE_FIRMWARE("cis/COMpad4.cis");
851 MODULE_FIRMWARE("cis/RS-COM-2P.cis");
852 
853 static struct pcmcia_driver serial_cs_driver = {
854         .owner          = THIS_MODULE,
855         .name           = "serial_cs",
856         .probe          = serial_probe,
857         .remove         = serial_detach,
858         .id_table       = serial_ids,
859         .suspend        = serial_suspend,
860         .resume         = serial_resume,
861 };
862 module_pcmcia_driver(serial_cs_driver);
863 
864 MODULE_LICENSE("GPL");
865 

This page was automatically generated by LXR 0.3.1 (source).  •  Linux is a registered trademark of Linus Torvalds  •  Contact us