Version:  2.0.40 2.2.26 2.4.37 3.13 3.14 3.15 3.16 3.17 3.18 3.19 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10

Linux/drivers/power/reset/Kconfig

  1 menuconfig POWER_RESET
  2         bool "Board level reset or power off"
  3         help
  4           Provides a number of drivers which either reset a complete board
  5           or shut it down, by manipulating the main power supply on the board.
  6 
  7           Say Y here to enable board reset and power off
  8 
  9 if POWER_RESET
 10 
 11 config POWER_RESET_AS3722
 12         bool "ams AS3722 power-off driver"
 13         depends on MFD_AS3722
 14         help
 15           This driver supports turning off board via a ams AS3722 power-off.
 16 
 17 config POWER_RESET_AT91_POWEROFF
 18         tristate "Atmel AT91 poweroff driver"
 19         depends on ARCH_AT91
 20         default SOC_AT91SAM9 || SOC_SAMA5
 21         help
 22           This driver supports poweroff for Atmel AT91SAM9 and SAMA5
 23           SoCs
 24 
 25 config POWER_RESET_AT91_RESET
 26         tristate "Atmel AT91 reset driver"
 27         depends on ARCH_AT91
 28         default SOC_AT91SAM9 || SOC_SAMA5
 29         help
 30           This driver supports restart for Atmel AT91SAM9 and SAMA5
 31           SoCs
 32 
 33 config POWER_RESET_AT91_SAMA5D2_SHDWC
 34         tristate "Atmel AT91 SAMA5D2-Compatible shutdown controller driver"
 35         depends on ARCH_AT91 || COMPILE_TEST
 36         default SOC_SAMA5
 37         help
 38           This driver supports the alternate shutdown controller for some Atmel
 39           SAMA5 SoCs. It is present for example on SAMA5D2 SoC.
 40 
 41 config POWER_RESET_AXXIA
 42         bool "LSI Axxia reset driver"
 43         depends on ARCH_AXXIA
 44         help
 45           This driver supports restart for Axxia SoC.
 46 
 47           Say Y if you have an Axxia family SoC.
 48 
 49 config POWER_RESET_BRCMKONA
 50         bool "Broadcom Kona reset driver"
 51         depends on ARM || COMPILE_TEST
 52         default ARCH_BCM_MOBILE
 53         help
 54           This driver provides restart support for Broadcom Kona chips.
 55 
 56           Say Y here if you have a Broadcom Kona-based board and you wish
 57           to have restart support.
 58 
 59 config POWER_RESET_BRCMSTB
 60         bool "Broadcom STB reset driver"
 61         depends on ARM || MIPS || COMPILE_TEST
 62         depends on MFD_SYSCON
 63         default ARCH_BRCMSTB
 64         help
 65           This driver provides restart support for Broadcom STB boards.
 66 
 67           Say Y here if you have a Broadcom STB board and you wish
 68           to have restart support.
 69 
 70 config POWER_RESET_GPIO
 71         bool "GPIO power-off driver"
 72         depends on OF_GPIO
 73         help
 74           This driver supports turning off your board via a GPIO line.
 75           If your board needs a GPIO high/low to power down, say Y and
 76           create a binding in your devicetree.
 77 
 78 config POWER_RESET_GPIO_RESTART
 79         bool "GPIO restart driver"
 80         depends on OF_GPIO
 81         help
 82           This driver supports restarting your board via a GPIO line.
 83           If your board needs a GPIO high/low to restart, say Y and
 84           create a binding in your devicetree.
 85 
 86 config POWER_RESET_HISI
 87         bool "Hisilicon power-off driver"
 88         depends on ARCH_HISI
 89         help
 90           Reboot support for Hisilicon boards.
 91 
 92 config POWER_RESET_IMX
 93         bool "IMX6 power-off driver"
 94         depends on POWER_RESET && SOC_IMX6
 95         help
 96           This driver support power off external PMIC by PMIC_ON_REQ on i.mx6
 97           boards.If you want to use other pin to control external power,please
 98           say N here or disable in dts to make sure pm_power_off never be
 99           overwrote wrongly by this driver.
100 
101 config POWER_RESET_MSM
102         bool "Qualcomm MSM power-off driver"
103         depends on ARCH_QCOM
104         help
105           Power off and restart support for Qualcomm boards.
106 
107 config POWER_RESET_PIIX4_POWEROFF
108         tristate "Intel PIIX4 power-off driver"
109         depends on PCI
110         depends on MIPS || COMPILE_TEST
111         help
112           This driver supports powering off a system using the Intel PIIX4
113           southbridge, for example the MIPS Malta development board. The
114           southbridge SOff state is entered in response to a request to
115           power off the system.
116 
117 config POWER_RESET_LTC2952
118         bool "LTC2952 PowerPath power-off driver"
119         depends on OF_GPIO
120         help
121           This driver supports an external powerdown trigger and board power
122           down via the LTC2952. Bindings are made in the device tree.
123 
124 config POWER_RESET_QNAP
125         bool "QNAP power-off driver"
126         depends on OF_GPIO && PLAT_ORION
127         help
128           This driver supports turning off QNAP NAS devices by sending
129           commands to the microcontroller which controls the main power.
130 
131           Say Y if you have a QNAP NAS.
132 
133 config POWER_RESET_RESTART
134         bool "Restart power-off driver"
135         help
136           Some boards don't actually have the ability to power off.
137           Instead they restart, and u-boot holds the SoC until the
138           user presses a key. u-boot then boots into Linux.
139 
140 config POWER_RESET_ST
141         bool "ST restart driver"
142         depends on ARCH_STI
143         help
144           Reset support for STMicroelectronics boards.
145 
146 config POWER_RESET_VERSATILE
147         bool "ARM Versatile family reboot driver"
148         depends on ARM
149         depends on MFD_SYSCON
150         depends on OF
151         help
152           Power off and restart support for ARM Versatile family of
153           reference boards.
154 
155 config POWER_RESET_VEXPRESS
156         bool "ARM Versatile Express power-off and reset driver"
157         depends on ARM || ARM64
158         depends on VEXPRESS_CONFIG
159         help
160           Power off and reset support for the ARM Ltd. Versatile
161           Express boards.
162 
163 config POWER_RESET_XGENE
164         bool "APM SoC X-Gene reset driver"
165         depends on ARM64
166         help
167           Reboot support for the APM SoC X-Gene Eval boards.
168 
169 config POWER_RESET_KEYSTONE
170         bool "Keystone reset driver"
171         depends on ARCH_KEYSTONE || COMPILE_TEST
172         depends on HAS_IOMEM
173         select MFD_SYSCON
174         help
175           Reboot support for the KEYSTONE SoCs.
176 
177 config POWER_RESET_SYSCON
178         bool "Generic SYSCON regmap reset driver"
179         depends on OF
180         depends on HAS_IOMEM
181         select MFD_SYSCON
182         help
183           Reboot support for generic SYSCON mapped register reset.
184 
185 config POWER_RESET_SYSCON_POWEROFF
186         bool "Generic SYSCON regmap poweroff driver"
187         depends on OF
188         depends on HAS_IOMEM
189         select MFD_SYSCON
190         help
191           Poweroff support for generic SYSCON mapped register poweroff.
192 
193 config POWER_RESET_RMOBILE
194         tristate "Renesas R-Mobile reset driver"
195         depends on ARCH_RMOBILE || COMPILE_TEST
196         depends on HAS_IOMEM
197         help
198           Reboot support for Renesas R-Mobile and SH-Mobile SoCs.
199 
200 config POWER_RESET_ZX
201         tristate "ZTE SoCs reset driver"
202         depends on ARCH_ZX || COMPILE_TEST
203         depends on HAS_IOMEM
204         help
205           Reboot support for ZTE SoCs.
206 
207 config REBOOT_MODE
208         tristate
209 
210 config SYSCON_REBOOT_MODE
211         tristate "Generic SYSCON regmap reboot mode driver"
212         depends on OF
213         depends on MFD_SYSCON
214         select REBOOT_MODE
215         help
216           Say y here will enable reboot mode driver. This will
217           get reboot mode arguments and store it in SYSCON mapped
218           register, then the bootloader can read it to take different
219           action according to the mode.
220 
221 endif
222 

This page was automatically generated by LXR 0.3.1 (source).  •  Linux is a registered trademark of Linus Torvalds  •  Contact us