Version:  2.0.40 2.2.26 2.4.37 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8

Linux/drivers/net/wan/Kconfig

  1 #
  2 # wan devices configuration
  3 #
  4 
  5 menuconfig WAN
  6         bool "Wan interfaces support"
  7         ---help---
  8           Wide Area Networks (WANs), such as X.25, Frame Relay and leased
  9           lines, are used to interconnect Local Area Networks (LANs) over vast
 10           distances with data transfer rates significantly higher than those
 11           achievable with commonly used asynchronous modem connections.
 12 
 13           Usually, a quite expensive external device called a `WAN router' is
 14           needed to connect to a WAN. As an alternative, a relatively
 15           inexpensive WAN interface card can allow your Linux box to directly
 16           connect to a WAN.
 17 
 18           If you have one of those cards and wish to use it under Linux,
 19           say Y here and also to the WAN driver for your card.
 20 
 21           If unsure, say N.
 22 
 23 if WAN
 24 
 25 # There is no way to detect a comtrol sv11 - force it modular for now.
 26 config HOSTESS_SV11
 27         tristate "Comtrol Hostess SV-11 support"
 28         depends on ISA && m && ISA_DMA_API && INET && HDLC && VIRT_TO_BUS
 29         help
 30           Driver for Comtrol Hostess SV-11 network card which
 31           operates on low speed synchronous serial links at up to
 32           256Kbps, supporting PPP and Cisco HDLC.
 33 
 34           The driver will be compiled as a module: the
 35           module will be called hostess_sv11.
 36 
 37 # The COSA/SRP driver has not been tested as non-modular yet.
 38 config COSA
 39         tristate "COSA/SRP sync serial boards support"
 40         depends on ISA && m && ISA_DMA_API && HDLC && VIRT_TO_BUS
 41         ---help---
 42           Driver for COSA and SRP synchronous serial boards.
 43 
 44           These boards allow to connect synchronous serial devices (for example
 45           base-band modems, or any other device with the X.21, V.24, V.35 or
 46           V.36 interface) to your Linux box. The cards can work as the
 47           character device, synchronous PPP network device, or the Cisco HDLC
 48           network device.
 49 
 50           You will need user-space utilities COSA or SRP boards for downloading
 51           the firmware to the cards and to set them up. Look at the
 52           <http://www.fi.muni.cz/~kas/cosa/> for more information. You can also
 53           read the comment at the top of the <file:drivers/net/wan/cosa.c> for
 54           details about the cards and the driver itself.
 55 
 56           The driver will be compiled as a module: the
 57           module will be called cosa.
 58 
 59 #
 60 # Lan Media's board. Currently 1000, 1200, 5200, 5245
 61 #
 62 config LANMEDIA
 63         tristate "LanMedia Corp. SSI/V.35, T1/E1, HSSI, T3 boards"
 64         depends on PCI && VIRT_TO_BUS && HDLC
 65         ---help---
 66           Driver for the following Lan Media family of serial boards:
 67 
 68           - LMC 1000 board allows you to connect synchronous serial devices
 69           (for example base-band modems, or any other device with the X.21,
 70           V.24, V.35 or V.36 interface) to your Linux box.
 71 
 72           - LMC 1200 with on board DSU board allows you to connect your Linux
 73           box directly to a T1 or E1 circuit.
 74 
 75           - LMC 5200 board provides a HSSI interface capable of running up to
 76           52 Mbits per second.
 77 
 78           - LMC 5245 board connects directly to a T3 circuit saving the
 79           additional external hardware.
 80 
 81           To change setting such as clock source you will need lmcctl.
 82           It is available at <ftp://ftp.lanmedia.com/> (broken link).
 83 
 84           To compile this driver as a module, choose M here: the
 85           module will be called lmc.
 86 
 87 # There is no way to detect a Sealevel board. Force it modular
 88 config SEALEVEL_4021
 89         tristate "Sealevel Systems 4021 support"
 90         depends on ISA && m && ISA_DMA_API && INET && HDLC && VIRT_TO_BUS
 91         help
 92           This is a driver for the Sealevel Systems ACB 56 serial I/O adapter.
 93 
 94           The driver will be compiled as a module: the
 95           module will be called sealevel.
 96 
 97 # Generic HDLC
 98 config HDLC
 99         tristate "Generic HDLC layer"
100         help
101           Say Y to this option if your Linux box contains a WAN (Wide Area
102           Network) card supported by this driver and you are planning to
103           connect the box to a WAN.
104 
105           You will need supporting software from
106           <http://www.kernel.org/pub/linux/utils/net/hdlc/>.
107           Generic HDLC driver currently supports raw HDLC, Cisco HDLC, Frame
108           Relay, synchronous Point-to-Point Protocol (PPP) and X.25.
109 
110           To compile this driver as a module, choose M here: the
111           module will be called hdlc.
112 
113           If unsure, say N.
114 
115 config HDLC_RAW
116         tristate "Raw HDLC support"
117         depends on HDLC
118         help
119           Generic HDLC driver supporting raw HDLC over WAN connections.
120 
121           If unsure, say N.
122 
123 config HDLC_RAW_ETH
124         tristate "Raw HDLC Ethernet device support"
125         depends on HDLC
126         help
127           Generic HDLC driver supporting raw HDLC Ethernet device emulation
128           over WAN connections.
129 
130           You will need it for Ethernet over HDLC bridges.
131 
132           If unsure, say N.
133 
134 config HDLC_CISCO
135         tristate "Cisco HDLC support"
136         depends on HDLC
137         help
138           Generic HDLC driver supporting Cisco HDLC over WAN connections.
139 
140           If unsure, say N.
141 
142 config HDLC_FR
143         tristate "Frame Relay support"
144         depends on HDLC
145         help
146           Generic HDLC driver supporting Frame Relay over WAN connections.
147 
148           If unsure, say N.
149 
150 config HDLC_PPP
151         tristate "Synchronous Point-to-Point Protocol (PPP) support"
152         depends on HDLC
153         help
154           Generic HDLC driver supporting PPP over WAN connections.
155 
156           If unsure, say N.
157 
158 config HDLC_X25
159         tristate "X.25 protocol support"
160         depends on HDLC && (LAPB=m && HDLC=m || LAPB=y)
161         help
162           Generic HDLC driver supporting X.25 over WAN connections.
163 
164           If unsure, say N.
165 
166 comment "X.25/LAPB support is disabled"
167         depends on HDLC && (LAPB!=m || HDLC!=m) && LAPB!=y
168 
169 config PCI200SYN
170         tristate "Goramo PCI200SYN support"
171         depends on HDLC && PCI
172         help
173           Driver for PCI200SYN cards by Goramo sp. j.
174 
175           If you have such a card, say Y here and see
176           <http://www.kernel.org/pub/linux/utils/net/hdlc/>.
177 
178           To compile this as a module, choose M here: the
179           module will be called pci200syn.
180 
181           If unsure, say N.
182 
183 config WANXL
184         tristate "SBE Inc. wanXL support"
185         depends on HDLC && PCI
186         help
187           Driver for wanXL PCI cards by SBE Inc.
188 
189           If you have such a card, say Y here and see
190           <http://www.kernel.org/pub/linux/utils/net/hdlc/>.
191 
192           To compile this as a module, choose M here: the
193           module will be called wanxl.
194 
195           If unsure, say N.
196 
197 config WANXL_BUILD_FIRMWARE
198         bool "rebuild wanXL firmware"
199         depends on WANXL && !PREVENT_FIRMWARE_BUILD
200         help
201           Allows you to rebuild firmware run by the QUICC processor.
202           It requires as68k, ld68k and hexdump programs.
203 
204           You should never need this option, say N.
205 
206 config PC300TOO
207         tristate "Cyclades PC300 RSV/X21 alternative support"
208         depends on HDLC && PCI
209         help
210           Alternative driver for PC300 RSV/X21 PCI cards made by
211           Cyclades, Inc. If you have such a card, say Y here and see
212           <http://www.kernel.org/pub/linux/utils/net/hdlc/>.
213 
214           To compile this as a module, choose M here: the module
215           will be called pc300too.
216 
217           If unsure, say N here.
218 
219 config N2
220         tristate "SDL RISCom/N2 support"
221         depends on HDLC && ISA
222         help
223           Driver for RISCom/N2 single or dual channel ISA cards by
224           SDL Communications Inc.
225 
226           If you have such a card, say Y here and see
227           <http://www.kernel.org/pub/linux/utils/net/hdlc/>.
228 
229           Note that N2csu and N2dds cards are not supported by this driver.
230 
231           To compile this driver as a module, choose M here: the module
232           will be called n2.
233 
234           If unsure, say N.
235 
236 config C101
237         tristate "Moxa C101 support"
238         depends on HDLC && ISA
239         help
240           Driver for C101 SuperSync ISA cards by Moxa Technologies Co., Ltd.
241 
242           If you have such a card, say Y here and see
243           <http://www.kernel.org/pub/linux/utils/net/hdlc/>.
244 
245           To compile this driver as a module, choose M here: the
246           module will be called c101.
247 
248           If unsure, say N.
249 
250 config FARSYNC
251         tristate "FarSync T-Series support"
252         depends on HDLC && PCI
253         ---help---
254           Support for the FarSync T-Series X.21 (and V.35/V.24) cards by
255           FarSite Communications Ltd.
256 
257           Synchronous communication is supported on all ports at speeds up to
258           8Mb/s (128K on V.24) using synchronous PPP, Cisco HDLC, raw HDLC,
259           Frame Relay or X.25/LAPB.
260 
261           If you want the module to be automatically loaded when the interface
262           is referenced then you should add "alias hdlcX farsync" to a file
263           in /etc/modprobe.d/ for each interface, where X is 0, 1, 2, ..., or
264           simply use "alias hdlc* farsync" to indicate all of them.
265 
266           To compile this driver as a module, choose M here: the
267           module will be called farsync.
268 
269 config DSCC4
270         tristate "Etinc PCISYNC serial board support"
271         depends on HDLC && PCI && m
272         help
273           Driver for Etinc PCISYNC boards based on the Infineon (ex. Siemens)
274           DSCC4 chipset.
275 
276           This is supposed to work with the four port card. Take a look at
277           <http://www.cogenit.fr/dscc4/> for further information about the
278           driver.
279 
280           To compile this driver as a module, choose M here: the
281           module will be called dscc4.
282 
283 config FSL_UCC_HDLC
284         tristate "Freescale QUICC Engine HDLC support"
285         depends on HDLC
286         depends on QUICC_ENGINE
287         help
288           Driver for Freescale QUICC Engine HDLC controller. The driver
289           supports HDLC in NMSI and TDM mode.
290 
291           To compile this driver as a module, choose M here: the
292           module will be called fsl_ucc_hdlc.
293 
294 config SLIC_DS26522
295         tristate "Slic Maxim ds26522 card support"
296         depends on SPI
297         depends on FSL_SOC || ARCH_MXC || ARCH_LAYERSCAPE
298         help
299           This module initializes and configures the slic maxim card
300           in T1 or E1 mode.
301 
302           To compile this driver as a module, choose M here: the
303           module will be called slic_ds26522.
304 
305 config DSCC4_PCISYNC
306         bool "Etinc PCISYNC features"
307         depends on DSCC4
308         help
309           Due to Etinc's design choice for its PCISYNC cards, some operations
310           are only allowed on specific ports of the DSCC4. This option is the
311           only way for the driver to know that it shouldn't return a success
312           code for these operations.
313 
314           Please say Y if your card is an Etinc's PCISYNC.
315 
316 config DSCC4_PCI_RST
317         bool "Hard reset support"
318         depends on DSCC4
319         help
320           Various DSCC4 bugs forbid any reliable software reset of the ASIC.
321           As a replacement, some vendors provide a way to assert the PCI #RST
322           pin of DSCC4 through the GPIO port of the card. If you choose Y,
323           the driver will make use of this feature before module removal
324           (i.e. rmmod). The feature is known to be available on Commtech's
325           cards. Contact your manufacturer for details.
326 
327           Say Y if your card supports this feature.
328 
329 config IXP4XX_HSS
330         tristate "Intel IXP4xx HSS (synchronous serial port) support"
331         depends on HDLC && ARM && ARCH_IXP4XX && IXP4XX_NPE && IXP4XX_QMGR
332         help
333           Say Y here if you want to use built-in HSS ports
334           on IXP4xx processor.
335 
336 config DLCI
337         tristate "Frame Relay DLCI support"
338         ---help---
339           Support for the Frame Relay protocol.
340 
341           Frame Relay is a fast low-cost way to connect to a remote Internet
342           access provider or to form a private wide area network. The one
343           physical line from your box to the local "switch" (i.e. the entry
344           point to the Frame Relay network, usually at the phone company) can
345           carry several logical point-to-point connections to other computers
346           connected to the Frame Relay network. For a general explanation of
347           the protocol, check out <http://www.mplsforum.org/>.
348 
349           To use frame relay, you need supporting hardware (called FRAD) and
350           certain programs from the net-tools package as explained in
351           <file:Documentation/networking/framerelay.txt>.
352 
353           To compile this driver as a module, choose M here: the
354           module will be called dlci.
355 
356 config DLCI_MAX
357         int "Max DLCI per device"
358         depends on DLCI
359         default "8"
360         help
361           How many logical point-to-point frame relay connections (the
362           identifiers of which are called DCLIs) should be handled by each
363           of your hardware frame relay access devices.
364 
365           Go with the default.
366 
367 config SDLA
368         tristate "SDLA (Sangoma S502/S508) support"
369         depends on DLCI && ISA
370         help
371           Driver for the Sangoma S502A, S502E, and S508 Frame Relay Access
372           Devices.
373 
374           These are multi-protocol cards, but only Frame Relay is supported
375           by the driver at this time. Please read
376           <file:Documentation/networking/framerelay.txt>.
377 
378           To compile this driver as a module, choose M here: the
379           module will be called sdla.
380 
381 # X.25 network drivers
382 config LAPBETHER
383         tristate "LAPB over Ethernet driver"
384         depends on LAPB && X25
385         ---help---
386           Driver for a pseudo device (typically called /dev/lapb0) which allows
387           you to open an LAPB point-to-point connection to some other computer
388           on your Ethernet network.
389 
390           In order to do this, you need to say Y or M to the driver for your
391           Ethernet card as well as to "LAPB Data Link Driver".
392 
393           To compile this driver as a module, choose M here: the
394           module will be called lapbether.
395 
396           If unsure, say N.
397 
398 config X25_ASY
399         tristate "X.25 async driver"
400         depends on LAPB && X25 && TTY
401         ---help---
402           Send and receive X.25 frames over regular asynchronous serial
403           lines such as telephone lines equipped with ordinary modems.
404 
405           Experts should note that this driver doesn't currently comply with
406           the asynchronous HDLS framing protocols in CCITT recommendation X.25.
407 
408           To compile this driver as a module, choose M here: the
409           module will be called x25_asy.
410 
411           If unsure, say N.
412 
413 config SBNI
414         tristate "Granch SBNI12 Leased Line adapter support"
415         depends on X86
416         ---help---
417           Driver for ISA SBNI12-xx cards which are low cost alternatives to
418           leased line modems.
419 
420           You can find more information and last versions of drivers and
421           utilities at <http://www.granch.ru/>. If you have any question you
422           can send email to <sbni@granch.ru>.
423 
424           To compile this driver as a module, choose M here: the
425           module will be called sbni.
426 
427           If unsure, say N.
428 
429 config SBNI_MULTILINE
430         bool "Multiple line feature support"
431         depends on SBNI
432         help
433           Schedule traffic for some parallel lines, via SBNI12 adapters.
434 
435           If you have two computers connected with two parallel lines it's
436           possible to increase transfer rate nearly twice. You should have
437           a program named 'sbniconfig' to configure adapters.
438 
439           If unsure, say N.
440 
441 endif # WAN

This page was automatically generated by LXR 0.3.1 (source).  •  Linux is a registered trademark of Linus Torvalds  •  Contact us