Version:  2.0.40 2.2.26 2.4.37 2.6.39 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15

Linux/drivers/net/hamradio/Kconfig

  1 config MKISS
  2         tristate "Serial port KISS driver"
  3         depends on AX25 && TTY
  4         select CRC16
  5         ---help---
  6           KISS is a protocol used for the exchange of data between a computer
  7           and a Terminal Node Controller (a small embedded system commonly
  8           used for networking over AX.25 amateur radio connections; it
  9           connects the computer's serial port with the radio's microphone
 10           input and speaker output).
 11 
 12           Although KISS is less advanced than the 6pack protocol, it has
 13           the advantage that it is already supported by most modern TNCs
 14           without the need for a firmware upgrade.
 15 
 16           To compile this driver as a module, choose M here: the module
 17           will be called mkiss.
 18 
 19 config 6PACK
 20         tristate "Serial port 6PACK driver"
 21         depends on AX25 && TTY
 22         ---help---
 23           6pack is a transmission protocol for the data exchange between your
 24           PC and your TNC (the Terminal Node Controller acts as a kind of
 25           modem connecting your computer's serial port to your radio's
 26           microphone input and speaker output). This protocol can be used as
 27           an alternative to KISS for networking over AX.25 amateur radio
 28           connections, but it has some extended functionality.
 29 
 30           Note that this driver is still experimental and might cause
 31           problems. For details about the features and the usage of the
 32           driver, read <file:Documentation/networking/6pack.txt>.
 33 
 34           To compile this driver as a module, choose M here: the module
 35           will be called 6pack.
 36 
 37 config BPQETHER
 38         tristate "BPQ Ethernet driver"
 39         depends on AX25
 40         help
 41           AX.25 is the protocol used for computer communication over amateur
 42           radio. If you say Y here, you will be able to send and receive AX.25
 43           traffic over Ethernet (also called "BPQ AX.25"), which could be
 44           useful if some other computer on your local network has a direct
 45           amateur radio connection.
 46 
 47 config DMASCC
 48         tristate "High-speed (DMA) SCC driver for AX.25"
 49         depends on ISA && AX25 && BROKEN_ON_SMP && ISA_DMA_API
 50         ---help---
 51           This is a driver for high-speed SCC boards, i.e. those supporting
 52           DMA on one port. You usually use those boards to connect your
 53           computer to an amateur radio modem (such as the WA4DSY 56kbps
 54           modem), in order to send and receive AX.25 packet radio network
 55           traffic.
 56 
 57           Currently, this driver supports Ottawa PI/PI2, Paccomm/Gracilis
 58           PackeTwin, and S5SCC/DMA boards. They are detected automatically.
 59           If you have one of these cards, say Y here and read the AX25-HOWTO,
 60           available from <http://www.tldp.org/docs.html#howto>.
 61 
 62           This driver can operate multiple boards simultaneously. If you
 63           compile it as a module (by saying M instead of Y), it will be called
 64           dmascc. If you don't pass any parameter to the driver, all
 65           possible I/O addresses are probed. This could irritate other devices
 66           that are currently not in use. You may specify the list of addresses
 67           to be probed by "dmascc.io=addr1,addr2,..." (when compiled into the
 68           kernel image) or "io=addr1,addr2,..." (when loaded as a module). The
 69           network interfaces will be called dmascc0 and dmascc1 for the board
 70           detected first, dmascc2 and dmascc3 for the second one, and so on.
 71 
 72           Before you configure each interface with ifconfig, you MUST set
 73           certain parameters, such as channel access timing, clock mode, and
 74           DMA channel. This is accomplished with a small utility program,
 75           dmascc_cfg, available at
 76           <http://www.linux-ax25.org/wiki/Ax25-tools>. Please be sure to
 77           get at least version 1.27 of dmascc_cfg, as older versions will not
 78           work with the current driver.
 79 
 80 config SCC
 81         tristate "Z8530 SCC driver"
 82         depends on ISA && AX25 && ISA_DMA_API
 83         ---help---
 84           These cards are used to connect your Linux box to an amateur radio
 85           in order to communicate with other computers. If you want to use
 86           this, read <file:Documentation/networking/z8530drv.txt> and the
 87           AX25-HOWTO, available from
 88           <http://www.tldp.org/docs.html#howto>. Also make sure to say Y
 89           to "Amateur Radio AX.25 Level 2" support.
 90 
 91           To compile this driver as a module, choose M here: the module
 92           will be called scc.
 93 
 94 config SCC_DELAY
 95         bool "additional delay for PA0HZP OptoSCC compatible boards"
 96         depends on SCC
 97         help
 98           Say Y here if you experience problems with the SCC driver not
 99           working properly; please read
100           <file:Documentation/networking/z8530drv.txt> for details.
101 
102           If unsure, say N.
103 
104 config SCC_TRXECHO
105         bool "support for TRX that feedback the tx signal to rx"
106         depends on SCC
107         help
108           Some transmitters feed the transmitted signal back to the receive
109           line.  Say Y here to foil this by explicitly disabling the receiver
110           during data transmission.
111 
112           If in doubt, say Y.
113 
114 config BAYCOM_SER_FDX
115         tristate "BAYCOM ser12 fullduplex driver for AX.25"
116         depends on AX25 && !S390
117         select CRC_CCITT
118         ---help---
119           This is one of two drivers for Baycom style simple amateur radio
120           modems that connect to a serial interface. The driver supports the
121           ser12 design in full-duplex mode. In addition, it allows the
122           baudrate to be set between 300 and 4800 baud (however not all modems
123           support all baudrates). This is the preferred driver. The next
124           driver, "BAYCOM ser12 half-duplex driver for AX.25" is the old
125           driver and still provided in case this driver does not work with
126           your serial interface chip. To configure the driver, use the sethdlc
127           utility available in the standard ax25 utilities package. For
128           information on the modems, see <http://www.baycom.de/> and
129           <file:Documentation/networking/baycom.txt>.
130 
131           To compile this driver as a module, choose M here: the module
132           will be called baycom_ser_fdx.  This is recommended.
133 
134 config BAYCOM_SER_HDX
135         tristate "BAYCOM ser12 halfduplex driver for AX.25"
136         depends on AX25 && !S390
137         select CRC_CCITT
138         ---help---
139           This is one of two drivers for Baycom style simple amateur radio
140           modems that connect to a serial interface. The driver supports the
141           ser12 design in half-duplex mode. This is the old driver.  It is
142           still provided in case your serial interface chip does not work with
143           the full-duplex driver. This driver is deprecated.  To configure
144           the driver, use the sethdlc utility available in the standard ax25
145           utilities package. For information on the modems, see
146           <http://www.baycom.de/> and
147           <file:Documentation/networking/baycom.txt>.
148 
149           To compile this driver as a module, choose M here: the module
150           will be called baycom_ser_hdx.  This is recommended.
151 
152 config BAYCOM_PAR
153         tristate "BAYCOM picpar and par96 driver for AX.25"
154         depends on PARPORT && AX25
155         select CRC_CCITT
156         ---help---
157           This is a driver for Baycom style simple amateur radio modems that
158           connect to a parallel interface. The driver supports the picpar and
159           par96 designs. To configure the driver, use the sethdlc utility
160           available in the standard ax25 utilities package. For information on
161           the modems, see <http://www.baycom.de/> and the file
162           <file:Documentation/networking/baycom.txt>.
163 
164           To compile this driver as a module, choose M here: the module
165           will be called baycom_par.  This is recommended.
166 
167 config BAYCOM_EPP
168         tristate "BAYCOM epp driver for AX.25"
169         depends on PARPORT && AX25 && !64BIT
170         select CRC_CCITT
171         ---help---
172           This is a driver for Baycom style simple amateur radio modems that
173           connect to a parallel interface. The driver supports the EPP
174           designs. To configure the driver, use the sethdlc utility available
175           in the standard ax25 utilities package. For information on the
176           modems, see <http://www.baycom.de/> and the file
177           <file:Documentation/networking/baycom.txt>.
178 
179           To compile this driver as a module, choose M here: the module
180           will be called baycom_epp.  This is recommended.
181 
182 config YAM
183         tristate "YAM driver for AX.25"
184         depends on AX25 && !S390
185         help
186           The YAM is a modem for packet radio which connects to the serial
187           port and includes some of the functions of a Terminal Node
188           Controller. If you have one of those, say Y here.
189 
190           To compile this driver as a module, choose M here: the module
191           will be called yam.
192 
193  

This page was automatically generated by LXR 0.3.1 (source).  •  Linux is a registered trademark of Linus Torvalds  •  Contact us