Version:  2.0.40 2.2.26 2.4.37 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18

Linux/drivers/net/fddi/Kconfig

  1 #
  2 # FDDI network device configuration
  3 #
  4 
  5 config FDDI
  6         tristate "FDDI driver support"
  7         depends on PCI || EISA || TC
  8         ---help---
  9           Fiber Distributed Data Interface is a high speed local area network
 10           design; essentially a replacement for high speed Ethernet. FDDI can
 11           run over copper or fiber. If you are connected to such a network and
 12           want a driver for the FDDI card in your computer, say Y here (and
 13           then also Y to the driver for your FDDI card, below). Most people
 14           will say N.
 15 
 16 if FDDI
 17 
 18 config DEFXX
 19         tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
 20         depends on FDDI && (PCI || EISA || TC)
 21         ---help---
 22           This is support for the DIGITAL series of TURBOchannel (DEFTA),
 23           EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
 24           to a local FDDI network.
 25 
 26           To compile this driver as a module, choose M here: the module
 27           will be called defxx.  If unsure, say N.
 28 
 29 config DEFXX_MMIO
 30         bool
 31         prompt "Use MMIO instead of PIO" if PCI || EISA
 32         depends on DEFXX
 33         default n if PCI || EISA
 34         default y
 35         ---help---
 36           This instructs the driver to use EISA or PCI memory-mapped I/O
 37           (MMIO) as appropriate instead of programmed I/O ports (PIO).
 38           Enabling this gives an improvement in processing time in parts
 39           of the driver, but it may cause problems with EISA (DEFEA)
 40           adapters.  TURBOchannel does not have the concept of I/O ports,
 41           so MMIO is always used for these (DEFTA) adapters.
 42 
 43           If unsure, say N.
 44 
 45 config SKFP
 46         tristate "SysKonnect FDDI PCI support"
 47         depends on FDDI && PCI
 48         select BITREVERSE
 49         ---help---
 50           Say Y here if you have a SysKonnect FDDI PCI adapter.
 51           The following adapters are supported by this driver:
 52           - SK-5521 (SK-NET FDDI-UP)
 53           - SK-5522 (SK-NET FDDI-UP DAS)
 54           - SK-5541 (SK-NET FDDI-FP)
 55           - SK-5543 (SK-NET FDDI-LP)
 56           - SK-5544 (SK-NET FDDI-LP DAS)
 57           - SK-5821 (SK-NET FDDI-UP64)
 58           - SK-5822 (SK-NET FDDI-UP64 DAS)
 59           - SK-5841 (SK-NET FDDI-FP64)
 60           - SK-5843 (SK-NET FDDI-LP64)
 61           - SK-5844 (SK-NET FDDI-LP64 DAS)
 62           - Netelligent 100 FDDI DAS Fibre SC
 63           - Netelligent 100 FDDI SAS Fibre SC
 64           - Netelligent 100 FDDI DAS UTP
 65           - Netelligent 100 FDDI SAS UTP
 66           - Netelligent 100 FDDI SAS Fibre MIC
 67 
 68           Read <file:Documentation/networking/skfp.txt> for information about
 69           the driver.
 70 
 71           Questions concerning this driver can be addressed to:
 72           <linux@syskonnect.de>
 73 
 74           To compile this driver as a module, choose M here: the module
 75           will be called skfp.  This is recommended.
 76 
 77 endif # FDDI

This page was automatically generated by LXR 0.3.1 (source).  •  Linux is a registered trademark of Linus Torvalds  •  Contact us