Version:  2.0.40 2.2.26 2.4.37 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18

Linux/drivers/net/ethernet/stmicro/stmmac/Kconfig

  1 config STMMAC_ETH
  2         tristate "STMicroelectronics 10/100/1000 Ethernet driver"
  3         depends on HAS_IOMEM && HAS_DMA
  4         select MII
  5         select PHYLIB
  6         select CRC32
  7         select PTP_1588_CLOCK
  8         select RESET_CONTROLLER
  9         ---help---
 10           This is the driver for the Ethernet IPs are built around a
 11           Synopsys IP Core and only tested on the STMicroelectronics
 12           platforms.
 13 
 14 if STMMAC_ETH
 15 
 16 config STMMAC_PLATFORM
 17         bool "STMMAC Platform bus support"
 18         depends on STMMAC_ETH
 19         default y
 20         ---help---
 21           This selects the platform specific bus support for
 22           the stmmac device driver. This is the driver used
 23           on many embedded STM platforms based on ARM and SuperH
 24           processors.
 25           If you have a controller with this interface, say Y or M here.
 26 
 27           If unsure, say N.
 28 
 29 config DWMAC_MESON
 30         bool "Amlogic Meson dwmac support"
 31         depends on STMMAC_PLATFORM && ARCH_MESON
 32         help
 33           Support for Ethernet controller on Amlogic Meson SoCs.
 34 
 35           This selects the Amlogic Meson SoC glue layer support for
 36           the stmmac device driver. This driver is used for Meson6 and
 37           Meson8 SoCs.
 38 
 39 config DWMAC_SOCFPGA
 40         bool "SOCFPGA dwmac support"
 41         depends on STMMAC_PLATFORM && MFD_SYSCON && (ARCH_SOCFPGA || COMPILE_TEST)
 42         help
 43           Support for ethernet controller on Altera SOCFPGA
 44 
 45           This selects the Altera SOCFPGA SoC glue layer support
 46           for the stmmac device driver. This driver is used for
 47           arria5 and cyclone5 FPGA SoCs.
 48 
 49 config DWMAC_SUNXI
 50         bool "Allwinner GMAC support"
 51         depends on STMMAC_PLATFORM && ARCH_SUNXI
 52         default y
 53         ---help---
 54           Support for Allwinner A20/A31 GMAC ethernet controllers.
 55 
 56           This selects Allwinner SoC glue layer support for the
 57           stmmac device driver. This driver is used for A20/A31
 58           GMAC    ethernet controller.
 59 
 60 config DWMAC_STI
 61         bool "STi GMAC support"
 62         depends on STMMAC_PLATFORM && ARCH_STI
 63         default y
 64         ---help---
 65           Support for ethernet controller on STi SOCs.
 66 
 67           This selects STi SoC glue layer support for the stmmac
 68           device driver. This driver is used on for the STi series
 69           SOCs GMAC ethernet controller.
 70 
 71 config STMMAC_PCI
 72         bool "STMMAC PCI bus support"
 73         depends on STMMAC_ETH && PCI
 74         ---help---
 75           This is to select the Synopsys DWMAC available on PCI devices,
 76           if you have a controller with this interface, say Y or M here.
 77 
 78           This PCI support is tested on XLINX XC2V3000 FF1152AMT0221
 79           D1215994A VIRTEX FPGA board.
 80 
 81           If unsure, say N.
 82 
 83 config STMMAC_DEBUG_FS
 84         bool "Enable monitoring via sysFS "
 85         default n
 86         depends on STMMAC_ETH && DEBUG_FS
 87         ---help---
 88           The stmmac entry in /sys reports DMA TX/RX rings
 89           or (if supported) the HW cap register.
 90 
 91 config STMMAC_DA
 92         bool "STMMAC DMA arbitration scheme"
 93         default n
 94         ---help---
 95           Selecting this option, rx has priority over Tx (only for Giga
 96           Ethernet device).
 97           By default, the DMA arbitration scheme is based on Round-robin
 98           (rx:tx priority is 1:1).
 99 
100 endif

This page was automatically generated by LXR 0.3.1 (source).  •  Linux is a registered trademark of Linus Torvalds  •  Contact us