Version:  2.0.40 2.2.26 2.4.37 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16

Linux/drivers/net/ethernet/realtek/Kconfig

  1 #
  2 # Realtek device configuration
  3 #
  4 
  5 config NET_VENDOR_REALTEK
  6         bool "Realtek devices"
  7         default y
  8         depends on PCI || (PARPORT && X86)
  9         ---help---
 10           If you have a network (Ethernet) card belonging to this class, say Y
 11           and read the Ethernet-HOWTO, available from
 12           <http://www.tldp.org/docs.html#howto>.
 13 
 14           Note that the answer to this question doesn't directly affect the
 15           kernel: saying N will just cause the configurator to skip all
 16           the questions about Realtek devices. If you say Y, you will be asked for
 17           your specific card in the following questions.
 18 
 19 if NET_VENDOR_REALTEK
 20 
 21 config ATP
 22         tristate "AT-LAN-TEC/RealTek pocket adapter support"
 23         depends on PARPORT && X86
 24         select CRC32
 25         ---help---
 26           This is a network (Ethernet) device which attaches to your parallel
 27           port. Read <file:drivers/net/ethernet/realtek/atp.c> as well as the
 28           Ethernet-HOWTO, available from <http://www.tldp.org/docs.html#howto>,
 29           if you want to use this.  If you intend to use this driver, you
 30           should have said N to the "Parallel printer support", because the two
 31           drivers don't like each other.
 32 
 33           To compile this driver as a module, choose M here: the module
 34           will be called atp.
 35 
 36 config 8139CP
 37         tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support"
 38         depends on PCI
 39         select CRC32
 40         select MII
 41         ---help---
 42           This is a driver for the Fast Ethernet PCI network cards based on
 43           the RTL8139C+ chips. If you have one of those, say Y and read
 44           the Ethernet-HOWTO, available from
 45           <http://www.tldp.org/docs.html#howto>.
 46 
 47           To compile this driver as a module, choose M here: the module
 48           will be called 8139cp.  This is recommended.
 49 
 50 config 8139TOO
 51         tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
 52         depends on PCI
 53         select CRC32
 54         select MII
 55         ---help---
 56           This is a driver for the Fast Ethernet PCI network cards based on
 57           the RTL 8129/8130/8139 chips. If you have one of those, say Y and
 58           read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.
 59 
 60           To compile this driver as a module, choose M here: the module
 61           will be called 8139too.  This is recommended.
 62 
 63 config 8139TOO_PIO
 64         bool "Use PIO instead of MMIO"
 65         default y
 66         depends on 8139TOO
 67         ---help---
 68           This instructs the driver to use programmed I/O ports (PIO) instead
 69           of PCI shared memory (MMIO).  This can possibly solve some problems
 70           in case your mainboard has memory consistency issues.  If unsure,
 71           say N.
 72 
 73 config 8139TOO_TUNE_TWISTER
 74         bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
 75         depends on 8139TOO
 76         ---help---
 77           This implements a function which might come in handy in case you
 78           are using low quality on long cabling. It is required for RealTek
 79           RTL-8139 revision K boards, and totally unused otherwise.  It tries
 80           to match the transceiver to the cable characteristics. This is
 81           experimental since hardly documented by the manufacturer.
 82           If unsure, say Y.
 83 
 84 config 8139TOO_8129
 85         bool "Support for older RTL-8129/8130 boards"
 86         depends on 8139TOO
 87         ---help---
 88           This enables support for the older and uncommon RTL-8129 and
 89           RTL-8130 chips, which support MII via an external transceiver,
 90           instead of an internal one.  Disabling this option will save some
 91           memory by making the code size smaller.  If unsure, say Y.
 92 
 93 config 8139_OLD_RX_RESET
 94         bool "Use older RX-reset method"
 95         depends on 8139TOO
 96         ---help---
 97           The 8139too driver was recently updated to contain a more rapid
 98           reset sequence, in the face of severe receive errors.  This "new"
 99           RX-reset method should be adequate for all boards.  But if you
100           experience problems, you can enable this option to restore the
101           old RX-reset behavior.  If unsure, say N.
102 
103 config R8169
104         tristate "Realtek 8169 gigabit ethernet support"
105         depends on PCI
106         select FW_LOADER
107         select CRC32
108         select MII
109         ---help---
110           Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.
111 
112           To compile this driver as a module, choose M here: the module
113           will be called r8169.  This is recommended.
114 
115 endif # NET_VENDOR_REALTEK

This page was automatically generated by LXR 0.3.1 (source).  •  Linux is a registered trademark of Linus Torvalds  •  Contact us