Version:  2.0.40 2.2.26 2.4.37 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17

Linux/drivers/net/ethernet/qlogic/Kconfig

  1 #
  2 # QLogic network device configuration
  3 #
  4 
  5 config NET_VENDOR_QLOGIC
  6         bool "QLogic devices"
  7         default y
  8         depends on PCI
  9         ---help---
 10           If you have a network (Ethernet) card belonging to this class, say Y
 11           and read the Ethernet-HOWTO, available from
 12           <http://www.tldp.org/docs.html#howto>.
 13 
 14           Note that the answer to this question doesn't directly affect the
 15           kernel: saying N will just cause the configurator to skip all
 16           the questions about QLogic cards. If you say Y, you will be asked for
 17           your specific card in the following questions.
 18 
 19 if NET_VENDOR_QLOGIC
 20 
 21 config QLA3XXX
 22         tristate "QLogic QLA3XXX Network Driver Support"
 23         depends on PCI
 24         ---help---
 25           This driver supports QLogic ISP3XXX gigabit Ethernet cards.
 26 
 27           To compile this driver as a module, choose M here: the module
 28           will be called qla3xxx.
 29 
 30 config QLCNIC
 31         tristate "QLOGIC QLCNIC 1/10Gb Converged Ethernet NIC Support"
 32         depends on PCI
 33         select FW_LOADER
 34         ---help---
 35           This driver supports QLogic QLE8240 and QLE8242 Converged Ethernet
 36           devices.
 37 
 38 config QLCNIC_SRIOV
 39         bool "QLOGIC QLCNIC 83XX family SR-IOV Support"
 40         depends on QLCNIC && PCI_IOV
 41         default y
 42         ---help---
 43           This configuration parameter enables Single Root Input Output
 44           Virtualization support for QLE83XX Converged Ethernet devices.
 45           This allows for virtual function acceleration in virtualized
 46           environments.
 47 
 48 config QLCNIC_DCB
 49         bool "QLOGIC QLCNIC 82XX and 83XX family DCB Support"
 50         depends on QLCNIC && DCB
 51         default y
 52         ---help---
 53           This configuration parameter enables DCB support in QLE83XX
 54           and QLE82XX Converged Ethernet devices. This allows for DCB
 55           get operations support through rtNetlink interface. Only CEE
 56           mode of DCB is supported. PG and PFC values are related only
 57           to Tx.
 58 
 59 config QLCNIC_VXLAN
 60         bool "Virtual eXtensible Local Area Network (VXLAN) offload support"
 61         default n
 62         depends on QLCNIC && VXLAN && !(QLCNIC=y && VXLAN=m)
 63         ---help---
 64           This enables hardware offload support for VXLAN protocol over QLogic's
 65           84XX series adapters.
 66           Say Y here if you want to enable hardware offload support for
 67           Virtual eXtensible Local Area Network (VXLAN) in the driver.
 68 
 69 config QLCNIC_HWMON
 70         bool "QLOGIC QLCNIC 82XX and 83XX family HWMON support"
 71         depends on QLCNIC && HWMON && !(QLCNIC=y && HWMON=m)
 72         default y
 73         ---help---
 74           This configuration parameter can be used to read the
 75           board temperature in Converged Ethernet devices
 76           supported by qlcnic.
 77 
 78           This data is available via the hwmon sysfs interface.
 79 
 80 config QLGE
 81         tristate "QLogic QLGE 10Gb Ethernet Driver Support"
 82         depends on PCI
 83         ---help---
 84           This driver supports QLogic ISP8XXX 10Gb Ethernet cards.
 85 
 86           To compile this driver as a module, choose M here: the module
 87           will be called qlge.
 88 
 89 config NETXEN_NIC
 90         tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC"
 91         depends on PCI
 92         select FW_LOADER
 93         ---help---
 94           This enables the support for NetXen's Gigabit Ethernet card.
 95 
 96 endif # NET_VENDOR_QLOGIC

This page was automatically generated by LXR 0.3.1 (source).  •  Linux is a registered trademark of Linus Torvalds  •  Contact us