Version:  2.0.40 2.2.26 2.4.37 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7

Linux/drivers/net/ethernet/freescale/Kconfig

  1 #
  2 # Freescale device configuration
  3 #
  4 
  5 config NET_VENDOR_FREESCALE
  6         bool "Freescale devices"
  7         default y
  8         depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
  9                    M523x || M527x || M5272 || M528x || M520x || M532x || \
 10                    ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \
 11                    ARCH_LAYERSCAPE
 12         ---help---
 13           If you have a network (Ethernet) card belonging to this class, say Y.
 14 
 15           Note that the answer to this question doesn't directly affect the
 16           kernel: saying N will just cause the configurator to skip all
 17           the questions about Freescale devices. If you say Y, you will be
 18           asked for your specific card in the following questions.
 19 
 20 if NET_VENDOR_FREESCALE
 21 
 22 config FEC
 23         tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
 24         depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
 25                    ARCH_MXC || SOC_IMX28)
 26         default ARCH_MXC || SOC_IMX28 if ARM
 27         select PHYLIB
 28         select PTP_1588_CLOCK
 29         ---help---
 30           Say Y here if you want to use the built-in 10/100 Fast ethernet
 31           controller on some Motorola ColdFire and Freescale i.MX processors.
 32 
 33 config FEC_MPC52xx
 34         tristate "FEC MPC52xx driver"
 35         depends on PPC_MPC52xx && PPC_BESTCOMM
 36         select CRC32
 37         select PHYLIB
 38         select PPC_BESTCOMM_FEC
 39         ---help---
 40           This option enables support for the MPC5200's on-chip
 41           Fast Ethernet Controller
 42           If compiled as module, it will be called fec_mpc52xx.
 43 
 44 config FEC_MPC52xx_MDIO
 45         bool "FEC MPC52xx MDIO bus driver"
 46         depends on FEC_MPC52xx
 47         default y
 48         ---help---
 49           The MPC5200's FEC can connect to the Ethernet either with
 50           an external MII PHY chip or 10 Mbps 7-wire interface
 51           (Motorola? industry standard).
 52           If your board uses an external PHY connected to FEC, enable this.
 53           If not sure, enable.
 54           If compiled as module, it will be called fec_mpc52xx_phy.
 55 
 56 source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
 57 source "drivers/net/ethernet/freescale/fman/Kconfig"
 58 
 59 config FSL_PQ_MDIO
 60         tristate "Freescale PQ MDIO"
 61         select PHYLIB
 62         ---help---
 63           This driver supports the MDIO bus used by the gianfar and UCC drivers.
 64 
 65 config FSL_XGMAC_MDIO
 66         tristate "Freescale XGMAC MDIO"
 67         select PHYLIB
 68         select OF_MDIO
 69         ---help---
 70           This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
 71           on the FMan mEMAC (which supports both Clauses 22 and 45)
 72 
 73 config UCC_GETH
 74         tristate "Freescale QE Gigabit Ethernet"
 75         depends on QUICC_ENGINE
 76         select FSL_PQ_MDIO
 77         select PHYLIB
 78         ---help---
 79           This driver supports the Gigabit Ethernet mode of the QUICC Engine,
 80           which is available on some Freescale SOCs.
 81 
 82 config UGETH_TX_ON_DEMAND
 83         bool "Transmit on Demand support"
 84         depends on UCC_GETH
 85 
 86 config GIANFAR
 87         tristate "Gianfar Ethernet"
 88         select FSL_PQ_MDIO
 89         select PHYLIB
 90         select CRC32
 91         ---help---
 92           This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
 93           and MPC86xx family of chips, the eTSEC on LS1021A and the FEC
 94           on the 8540.
 95 
 96 endif # NET_VENDOR_FREESCALE

This page was automatically generated by LXR 0.3.1 (source).  •  Linux is a registered trademark of Linus Torvalds  •  Contact us