Version:  2.0.40 2.2.26 2.4.37 2.6.39 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15

Linux/drivers/extcon/Kconfig

  1 menuconfig EXTCON
  2         tristate "External Connector Class (extcon) support"
  3         help
  4           Say Y here to enable external connector class (extcon) support.
  5           This allows monitoring external connectors by userspace
  6           via sysfs and uevent and supports external connectors with
  7           multiple states; i.e., an extcon that may have multiple
  8           cables attached. For example, an external connector of a device
  9           may be used to connect an HDMI cable and a AC adaptor, and to
 10           host USB ports. Many of 30-pin connectors including PDMI are
 11           also good examples.
 12 
 13 if EXTCON
 14 
 15 comment "Extcon Device Drivers"
 16 
 17 config EXTCON_GPIO
 18         tristate "GPIO extcon support"
 19         depends on GPIOLIB
 20         help
 21           Say Y here to enable GPIO based extcon support. Note that GPIO
 22           extcon supports single state per extcon instance.
 23 
 24 config EXTCON_ADC_JACK
 25         tristate "ADC Jack extcon support"
 26         depends on IIO
 27         help
 28           Say Y here to enable extcon device driver based on ADC values.
 29 
 30 config EXTCON_MAX14577
 31         tristate "MAX14577 EXTCON Support"
 32         depends on MFD_MAX14577
 33         select IRQ_DOMAIN
 34         select REGMAP_I2C
 35         help
 36           If you say yes here you get support for the MUIC device of
 37           Maxim MAX14577 PMIC. The MAX14577 MUIC is a USB port accessory
 38           detector and switch.
 39 
 40 config EXTCON_MAX77693
 41         tristate "MAX77693 EXTCON Support"
 42         depends on MFD_MAX77693 && INPUT
 43         select IRQ_DOMAIN
 44         select REGMAP_I2C
 45         help
 46           If you say yes here you get support for the MUIC device of
 47           Maxim MAX77693 PMIC. The MAX77693 MUIC is a USB port accessory
 48           detector and switch.
 49 
 50 config EXTCON_MAX8997
 51         tristate "MAX8997 EXTCON Support"
 52         depends on MFD_MAX8997 && IRQ_DOMAIN
 53         help
 54           If you say yes here you get support for the MUIC device of
 55           Maxim MAX8997 PMIC. The MAX8997 MUIC is a USB port accessory
 56           detector and switch.
 57 
 58 config EXTCON_ARIZONA
 59         tristate "Wolfson Arizona EXTCON support"
 60         depends on MFD_ARIZONA && INPUT && SND_SOC
 61         help
 62           Say Y here to enable support for external accessory detection
 63           with Wolfson Arizona devices. These are audio CODECs with
 64           advanced audio accessory detection support.
 65 
 66 config EXTCON_PALMAS
 67         tristate "Palmas USB EXTCON support"
 68         depends on MFD_PALMAS
 69         help
 70           Say Y here to enable support for USB peripheral and USB host
 71           detection by palmas usb.
 72 
 73 endif # MULTISTATE_SWITCH

This page was automatically generated by LXR 0.3.1 (source).  •  Linux is a registered trademark of Linus Torvalds  •  Contact us