Version:  2.0.40 2.2.26 2.4.37 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18

Linux/arch/mips/netlogic/Kconfig

  1 if NLM_XLP_BOARD || NLM_XLR_BOARD
  2 
  3 if NLM_XLP_BOARD
  4 config DT_XLP_EVP
  5         bool "Built-in device tree for XLP EVP boards"
  6         default y
  7         select BUILTIN_DTB
  8         help
  9           Add an FDT blob for XLP EVP boards into the kernel.
 10           This DTB will be used if the firmware does not pass in a DTB
 11           pointer to the kernel.  The corresponding DTS file is at
 12           arch/mips/netlogic/dts/xlp_evp.dts
 13 
 14 config DT_XLP_SVP
 15         bool "Built-in device tree for XLP SVP boards"
 16         default y
 17         select BUILTIN_DTB
 18         help
 19           Add an FDT blob for XLP VP boards into the kernel.
 20           This DTB will be used if the firmware does not pass in a DTB
 21           pointer to the kernel.  The corresponding DTS file is at
 22           arch/mips/netlogic/dts/xlp_svp.dts
 23 
 24 config DT_XLP_FVP
 25         bool "Built-in device tree for XLP FVP boards"
 26         default y
 27         select BUILTIN_DTB
 28         help
 29           Add an FDT blob for XLP FVP board into the kernel.
 30           This DTB will be used if the firmware does not pass in a DTB
 31           pointer to the kernel.  The corresponding DTS file is at
 32           arch/mips/netlogic/dts/xlp_fvp.dts
 33 
 34 config DT_XLP_GVP
 35         bool "Built-in device tree for XLP GVP boards"
 36         default y
 37         select BUILTIN_DTB
 38         help
 39           Add an FDT blob for XLP GVP board into the kernel.
 40           This DTB will be used if the firmware does not pass in a DTB
 41           pointer to the kernel.  The corresponding DTS file is at
 42           arch/mips/netlogic/dts/xlp_gvp.dts
 43 
 44 config NLM_MULTINODE
 45         bool "Support for multi-chip boards"
 46         depends on NLM_XLP_BOARD
 47         default n
 48         help
 49           Add support for boards with 2 or 4 XLPs connected over ICI.
 50 
 51 if NLM_MULTINODE
 52 choice
 53         prompt "Number of XLPs on the board"
 54         default NLM_MULTINODE_2
 55         help
 56           In the multi-node case, specify the number of SoCs on the board.
 57 
 58 config NLM_MULTINODE_2
 59         bool "Dual-XLP board"
 60         help
 61           Support boards with upto two XLPs connected over ICI.
 62 
 63 config NLM_MULTINODE_4
 64         bool "Quad-XLP board"
 65         help
 66           Support boards with upto four XLPs connected over ICI.
 67 
 68 endchoice
 69 
 70 endif
 71 endif
 72 
 73 config NLM_COMMON
 74         bool
 75 
 76 config IOMMU_HELPER
 77         bool
 78 
 79 config NEED_SG_DMA_LENGTH
 80         bool
 81 
 82 config SWIOTLB
 83         def_bool y
 84         select NEED_SG_DMA_LENGTH
 85         select IOMMU_HELPER
 86 
 87 endif

This page was automatically generated by LXR 0.3.1 (source).  •  Linux is a registered trademark of Linus Torvalds  •  Contact us